Bedienungsanleitung Speroni ME (Seite 14 von 52) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

680566

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Problem How to check Remedy

1 Motor does

not start.

No noises

or vibrations

occur

2 Motor does

not start,

but generates

noises and

vibrations

A - Make sure that motor is wired up as

directed in the diagram inside the terminal

box cover.

B - The shaft is bound. Find out if due to loose

fan or mechanical obstructions on the

motor or the pump.

C - The sliding surface of mechanical seal is

stuck due to prolonged stoppage.

A - Correct any wrong

connections.

B - Remove cause of obstruction.

C - Correct seal by turning the

shaft - 1/4 turn with a pipe

wrench.

3 Pump

does not

provide

delivery

A - Pump has not been filled.

B - Pump has unprimed due to leaks in the

suction line.

C - With 3phase motors check for correct

direction of rotation.

D - The head required by the plant is higher

than that generated by the pump.

E - Foot valve clogged.

F - Suction lift too high.

G - Suction pipe too narrow.

A - Fill the pump. Prime it again.

B - Repair leaks. Fill and prime

again.

C - Interchange two supply leads.

D - Replace the pump with a

suitable one.

E - Clean foot valve.

F - See section “installation”.

G - Replace suction pipe with one

having diameter larger by 1/4”

or 1/2”.

A - Make sure that power supply

is connected.

B - Check for any blown fuses.

C - Check for open or dirty contacts in the

protection devices.

B - Replace fuse with new one.

Note: if the new fuse blows immediately

after, the motor or the cable are shorted,

either directly or the earth (faulty insulation).

C - Clean the part involved or

replace it with a new one.

4 Protection

trips

as machine

starts

A - One phase is missing.

B - As in 1B.

C - As in 1C.

D - Motor with faulty insulation; check phase

resistance and insulation to ground.

A - Reset the phase

B - As in 1B.

C - As in 1C.

D - Replace stator or the internal

earth cable.

8. Fault finding chart: problems, possible causes and remedies

INSTRUCTIONS FOR THE INSTALLATION AND USE OF ELECTROPUMPS

Problem How to check Remedy

5 Protection

trips

too often

6 Shaft

spins

with difficulty

A - Check for obstructions in the motor or the

pump.

B - As in 5D.

C - Check bearings for proper conditions.

A - As in 2B.

B - As in 5D.

C - Replace any faulty bearing.

A - Ascertain whether the protection device is

set to a value lower than the motor full load

requirements.

B - One phase is missing due to faults in

contacts or supply cable.

C - Liquid is viscous or its specific weight is

much higher than that of water.

D - Harsh rubbing occurs between sliding and

stationary parts.

A - Correct setting.

B - Clean and reset contact or

replace supply cable with new

one.

C - Reduce flow rate slightly by

adjusting the delivery sluice

valve accordingly. If this is not

acceptable, instal a more

powerful motor.

D - Remove cause of harsh

rubbing.

When stopped,

the pump runs

slightly in reverse

direction

A - Leaks or air locks in suction pipe. A - Correct leaks and read section

“installation”.

7 Pump

vibrates, runs

noisily;

flow rate

is uneven

A - Pump runs beyond rated capacity.

B - Pump or pipework not properly secured.

C - As in 3F.

D - As in 3G.

A - Reduce flow rate.

B - Secure any loose or improperly

secured part.

C - As in 3F.

D - As in 3G.

In pressure

boosting

applications the

pump starts and

stops too often

A - Pressure-switch setting is too limited.

B - Leaks in system.

A - Set pressure switch to wider

limits.

B - Eliminate leaks.

In pressure

boosting

applications, the

pump does not stop

A -

Max.-pressure setting in pressure switch

is too high.

B -

As in 9B

A - Reduce max-pressure setting

to lower value.

B - As in 9B.

8. Fault finding chart: problems, possible causes and remedies



Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Speroni ME Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info