Bedienungsanleitung Spirit EL07 (Seite 9 von 28) (Englisch)

583976

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Assembly Instructions

■ UNPACKING THE UNIT

1. Using a razor knife (Box Cutter) cut the outside, bottom, edge of box along the dotted Line. Lift

Box over the unit and unpack.

2. Carefully remove all parts from carton and inspect for any damage or missing parts. If damaged

parts are found, or parts are missing, contact your dealer immediately.

3. Locate the hardware package. The hardware is separated into steps. Remove the tools first.

Remove the hardware for each step as needed to avoid confusion. The numbers in the instructions

that are in parenthesis (#) are the item number from the assembly drawing, for reference.

STEP 1: Incline Rail Assembly and Console Mast

1. Install the Incline Rail Assembly (2) into the U-channel bracket of the Main Frame (1). Secure

with the six bolts & associated hardware as follows: From the sides install two 3/8”x1-1/2” Hex

Head Bolts (77) with two 3/8”x19mm Flat Washers (96) and two 3/8”x7T Nylon Nuts (89). From

the top install four 5/16”x2-1/4” Hex Head Bolts (167), four 5/16” Split Washers (178), four

5/16”x20 Flat Washers (100), and four 5/16” Star Washers (179), as shown in figure 1, and

tighten with the 13/14 mm Wrench (124) and 12/14mm Wrench (129).

2. Connect the three Incline Motor Power lines by matching the Red, White and Black color codes

of the wires (37) and the 3-pin position Sensor Connector (38).

Locate the Console Mast (12)

and

Console Mast Cover (49)

and

slide the Cover

onto

the Mast as

far as

will

go. Make sure

the Console Mast Cover is

facing the correct way. At the

top opening

the Main

Frame

the

elliptical

there

is a Computer Cable (39) and an incline cable (36). Unravel

and straighten out the

cables and feed them

into the

bottom of the console mast tube and out of the top

opening.

Install the Console Mast (12) into the receiving bracket on the top of the Main Frame (1). Pull

slightly on the cables at the top of the mast while installing. This will ensure the cable does not

get pinched and electrically shorted during the console mast assembly.

Put

one

3/8"

Split

Washer (128)

onto the

3/8"

2-1/4" Long

Hex

Head Bolt (75) and install

through the left side of

the receiving

bracket

into

the

Console

Mast (12). Put the

two 3/8

x 23

Curved

Washers (104)

onto the

two 3/8" x 3/4" Short Hex Head Bolts (76) and install through

the front of the console mast. Using

the

13/14m/m

Wrench,

tighten

the

three

bolts,

and

the

fourth bolt

, which

is pre-installed, firmly. These

bolts should be tightened as

much as

you

possibly can.

4. Plug all of the connectors into the back of the console; Computer Cable (39), two Hand pulse

Cables (44) and Incline cable (36). Secure the Console (32) on the console mounting plate with

four M5x10m/m Phillips Head Screws (85).

EL7 Elliptical

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Spirit EL07 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info