Bedienungsanleitung Spirit EL555 (Seite 9 von 26) (Englisch)

583980

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

EL555 Elliptical

UNPACKING THE UNIT

1. Using a razor knife (Box Cutter) cut the outside, bottom, edge of box along the dotted Line. Lift

Box over the unit and unpack.

2. Carefully remove all parts from carton and inspect for any damage or missing parts. If damaged

parts are found, or parts are missing, contact your dealer immediately.

3. Locate the hardware package. The hardware is separated into steps. Remove the tools first.

Remove the hardware for each step as needed to avoid confusion. The numbers in the instructions

that are in parenthesis (#) are the item number from the assembly drawing, for reference.

STEP 1: Incline Rail Assembly and Console Mast

1. Install the Incline Rail Assembly (2) into the U-channel bracket of the Main Frame (1). Secure

with the six bolts & associated hardware as follows: From the sides install two 3/8x1-1/2 Hex

Head Bolts (77) with two 3/8 Flat Washers (96) and two 3/8 Nuts (89). From the top install

four 5/16x2-1/4 Hex Head Bolts (167), four 5/16 Split Washers (178), four 5/16 Flat Washers

(100), and four 5/16 Star Washers (179), as shown in figure 1, and tighten securely.

2. Connect the three Incline Motor Power lines (your machine may have only one 3-pin power

connector) by matching the Red, White and Black color codes of the wires (37) and the 3-pin

position Sensor Connector (38).

Locate the Console Mast (12) and Console Mast Cover (49) and slide the Cover onto the Mast

as far as it will go. Make sure the Console Mast Cover is facing the correct way. At the top

opening of the Main Frame of the elliptical

there

is a Computer Cable (39). Unravel and

straighten out the cables and feed them into the bottom of the console mast tube and out of the

top opening.

Install the Console Mast (12) into the receiving bracket on the top of the Main

Frame (1). Pull slightly on the cables at the top of the mast while installing. This will ensure the

cable does not get pinched and electrically shorted during the console mast assembly.

Put one 3/8" x 2T Split Washer (128) onto the 3/8" x 2-1/4" Long Hex Head Bolt (75) and install

through the left side of the receiving bracket into the Console Mast (12). Put the two 3/8

x 23

Curved Washers (104) onto the two 3/8" x 3/4" Short Hex Head Bolts (76) and install through

the front of the console mast. Using the 13/14m/m Wrench, tighten the three bolts, and the

fourth bolt

, which

is pre-installed, firmly. These bolts should be tightened as much as you

possibly can.

5. Plug all of the connectors into the back of the console; Computer Cable (39), two Hand pulse

Cables (44) and Incline cable (36). Secure the Console (32) on the console mounting plate with

four M5x10m/m Phillips Head Screws (85).

Assembly Instructions

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Spirit EL555 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info