Bedienungsanleitung Spirit ET388 (Seite 17 von 20) (Englisch)

584039

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

ET288/ET388

TREADBELT TRACKING ADJUSTMENT:

The performance of your treadmill is dependent on the frame running on a reasonably level

surface. If the frame is not level, the front and back roller cannot run parallel, and constant belt

adjustment may be necessary.

The treadmill is designed to keep the tread-belt reasonably centered while in use. It is normal for

some belts to drift near one side while the belt is running with no one on it. After a few minutes of

use, the tread-belt should have a tendency to center itself. If, during use, the belt continues to

move towar

d one side, adjustments are necessary.

TO SET TREADBELT TRACKING:

A 6 mm Allen wrench is provided to adjust the rear roller. Make tracking adjustments from the

left side only. Set belt speed at

approximately 2 to 3 mph. A small

adjustment can make a dramatic difference.

Turn the bolt only a 1/4 turn and wait a few

minutes for the belt to adjust itself. Continue

to make 1/4 rotation turns until the belt

stabilizes in the center of the running deck.

The belt may require periodic tracking

adjustment depending on use and

walking/running characteristics. Some users

will affect tracking differently. Expect to make

adjustments

as required to center the tread-belt. Adjustments will become less of a maintenance

concern as the belt is used. Proper belt tracking is an owner responsibility common with all

treadmills.

ATTENTION:

DAMAGE TO THE RUNNING BELT RESULTING FROM IMPROPER TRACKING /

TENSION ADJUSTMENTS IS NOT COVERED UNDER THE SPIRIT WARRANTY.

MAINTENANCE MODE:

If you want to set the Speed and Distance to Metric or if there is a problem with the speed and

you would like to perform the calibration procedure, use the Maintenance Mode. To enter

Maintenance Mode press, and hold for 5 seconds, the Start and Fast keys while installing the

safety k

ey.

• The large display window will now be showing the Roller size. Roller size is used for the

calibration process and should be set to 2.36

• The large display window will also display the setting for M (miles) or K (Kilometers).

Press the Enter key to change between M and K.

• To run the calibration procedure, press the Start key.

o The display will show a number for the lowest speed setting (for miles the number

should be 0.5). Adjust the low speed setting with the Fast/Slow keys.

Using the

DOWN button, run the incline all the way down and press START.

o The display will show a number for the top speed setting (for Miles it should be

10.0). Adjust the top speed setting if needed. Using the UP button, run the incline

all the way up and press Start to begin calibration.

o The belt will start automatically and will adjust speeds between low and high. Be

careful because the belt will change speeds without warning. When the calibration

is finished the display will return to the start-up screen.

Using the DOWN button, run

the incline all the way down. Now you are ready to begin your workout.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Spirit ET388 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info