Bedienungsanleitung Spirit XE295 2009 (Seite 30 von 31) (Englisch)

584174

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

XE195 / XE295 Elliptical

Maintenance:

1. Wipe down all areas in the sweat path with a damp cloth after each workout.

2. If a squeak, thump, clicking or rough feeling develops the main cause is most likely one of two

reasons:

i. The hardware was not sufficiently tightened during assembly. All bolts that were

installed during assembly need to be tightened as much as possible. It may be

necessary to use a larger wrench than the one provided if you cannot tighten the

bolts sufficiently. I cannot stress this point enough; 90% of calls to the service

department for noise issues can be traced to loose hardware or the rear rails being

dirty.

ii. Dirt build-up on the rear rails and polyurethane wheels are also a source of noise.

Noise from build-up on the rails can cause a thumping sound that you would swear

is coming from inside the main body of the machine because noise travels, and is

amplified, in the tubing of the frame. Clean the rails and wheels with a lint free cloth

and rubbing alcohol. Stubborn build-up can be removed with your thumbnail or a

non-metallic scraper, like the back edge of a plastic knife. After cleaning, apply a

small amount of lubricant on the rails with your fingers or a lint free cloth. You only

need a thin coat of lubrication, wipe off any excess.

3. If squeaks or other noises persist, check that the unit is properly leveled. There are 4 leveling

pads on the bottom of the rear rails, use a 14mm wrench (or adjustable wrench) to adjust the

levelers.

Maintenance Menu in console software:

The console has built in maintenance/diagnostic software. The software will allow you to change

the console settings from English to Metric and turn off the beeping of the speaker when a key is

pressed for example. To enter the Maintenance menu (may be called Engineering mode,

depending on version) press and hold down the Start, Stop and Enter keys. Keep holding the keys

down for about 5 seconds and the message window will display “ALTXXXX Engineering mode”.

Press the enter button to access the menu below:

Key test

(will allow you to test all the keys to make sure they are functioning)

Display test (

tests all the display functions)

Functions

(Press enter to access settings)

Sleep mode

(Turn on to have the console power down automatically after

20 minutes of inactivity)

ii.

Safety

(On = workload set to level 20 on power-up)

iii.

Motor test

(Press enter to run the workload motor up and down in a

continuous loop. Display shows level setting and position sensor reading.

Press stop to end test.)

iv.

Beep

(Turn on or off the beep when a key is pressed)

Units

(Set to English or Metric display readings)

vi.

ODO reset

(reset the odometer)

vii.

Pause Mode

(Turn on allow 5 minutes of pause, turn off to have the

console pause indefinitely)

d. Security

(Allows you to lock the keypad so no unauthorized use is allowed)

Factory settings

(Access only allowed by manufacturing)

Exit

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Spirit XE295 2009 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info