Bedienungsanleitung Spirit XE300 2007 (Seite 10 von 45) (Englisch)

584177

Zoom out

Zoom in

Vorherige Seite

1/45

Nächste Seite

XE100 / XE200 / XE300 Elliptical

 UNPACKING THE UNIT

1. Using a razor knife (Box Cutter) cut the outside, bottom, edge of box along the dotted Line. Lift

Box over the unit and unpack.

2. Carefully remove all parts from carton and inspect for any damage or missing parts. If damaged

parts are found, or parts are missing, contact your dealer immediately.

3. Locate the hardware package. The hardware is separated into steps. Remove the tools first.

Remove the hardware for each step as needed to avoid confusion.

STEP 1: CONSOLE MAST ASSEMBLY

Locate the Console Mast (12) and Console Mast Cover (41) and slide the Cover onto the

Mast as far as it will go. Make sure the Console Mast Cover is facing the correct way.

2. At the top opening of the Main Frame of the elliptical is a Computer Cable. Unravel and

straighten out the Computer Cable (31) and feed it into the bottom of the console mast tube

and out of the top opening.

3. Install the Console Mast into the receiving bracket in the top of the Main Frame. NOTE: there

is one bolt already installed in the receiving bracket that will engage with the slot at the bottom

of the Console Mast. This needs to be tightened at the end along with the three other console

mast bolts.

4. Put one 3/8" x 2T Split Washer (96) onto the 3/8" x 2-1/4" Long Hex Head Bolt (60), and the

two 3/8

x 23 Curved Washers (84) onto the two 3/8" x 3/4" Short Hex Head Bolts (103).

Install, and hand tighten, the Long Hex Head Bolt through the left side of the receiving bracket

into the Console Mast.

NOTE:

There is an electrical wire running through the Console Mast Tube. Be careful not to

damage or pinch this Computer Cable during this procedure. Damage to the Console could

result. Install, and hand tighten, the two Short Hex Head bolts through the front of the

receiving bracket into the Console Mast.

5. Using the 13/14m/m Wrench tighten the three bolts and the fourth bolt, which is pre-installed,

firmly. These bolts should be tightened as much as you possibly can.

6. There will be three electrical wire connectors at the top opening of the console mast, two 2 pin

connectors (hand pulse sensors)(36) and one 10 pin connector (main wire harness)(31).

Connect these to the mating connectors on the back of the electronic Console (30). The

connectors are keyed, you cannot plug them in the wrong way so do not force them. The two,

2 pin connectors can be plugged into either connector on the back of the console.

7. Storing the excess wire back into the Console Mast, carefully install the Console onto the

mounting plate of Console Mast and secure using the four M5 x 10m/m Phillips Head Screws.

Make sure the wires do not get pinched between the console and mounting plate.

Assembly Instructions( XE100 / XE200)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Spirit XE300 2007 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info