Bedienungsanleitung Spirit XT185 - 2011-2012 (Seite 30 von 32) (Englisch)

583923

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Treadmill

XT185

If the calibration does not pass you may need to check the speed sensor alignment.

1. Remove the motor cover hood by loosening the 8 screws that hold it

in place. Set it aside.

2. The speed sensor is located on the left side of the frame, right next to the

front roller pulley (the pulley will have a belt around it that also goes to the

motor). The speed sensor is a small rectangular shaped black box with a

wire connected to it.

3. You will see a magnet on the outside edge of the pulley; make sure the

speed sensor is aligned with the center of the magnet when it passes by.

There are two a screws that hold the sensor in place that need to be

loosened to adjust the sensor. Re-tighten the screws when nished.

The console has built in maintenance/diagnostic software. The software will allow you to change

the console settings from English to Metric and turn off the beeping of the speaker when a key

is pressed for example. To enter the Engineering Mode Menu press and hold down the Start,

Stop and Enter keys, then insert the safety key. Keep holding the keys down until the Message

Center displays Engineering Mode Menu. Press the Enter button to access the menu below:

a. Key Test (Will allow you to test all the keys to make sure they are functioning)

b. Security (Allows the keypad to be locked to prevent unauthorized use)

c. Functions (Press Enter to access settings and Up arrow to scroll)

i. Sleep Mode (Turn on to have the console power down automatically after 20 minutes of inactivity)

ii. Motor Test (Press Enter to run the resistance motor up and down in a continuous loop. Display shows

level setting and position sensor reading. Press Stop to end test.)

iii. Beep (Turns off the speaker so no beeping sound is heard)

iv. Units (Sets the display to readout in English or Metric display measurements)

v. ODO Reset (Resets the odometer)

vi. Pause Mode (Turn on allow 5 minutes of pause, turn off to have the console pause indenitely)

d. LCD Test (Tests all the display functions)

Adjusting The Speed Sensor

Engineering Mode Menu

1. Remove the safety key

2. Press and hold down the Start and Fast + buttons and replace the safety key. Continue to hold the

Start and Fast key until the window displays “Factory settings”, then press the Enter key.

3. You will now be able to set the display to show Metric or English settings (Miles vs. Kilometers).

To do this, press the Up or Down key to show which you want, then press Enter.

4. Make sure the wheel size diameter is 2.30 then press Enter

5. Adjust the minimum speed (if needed) to 0.5 and then press Enter

6. Adjust the maximum speed (if needed) to 10.0 and then press Enter

7. Adjust the maximum elevation (if needed) to 12 and then press Enter

8. Grade return – On (This allows the incline to return to zero when Stop is pressed. For sale in

Europe, EU standards require this to be off)

9. Press Start to begin calibration. The process is automatic; the speed will start up without warning, so

do not stand on the belt.

Calibration Procedure

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Spirit XT185 - 2011-2012 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info