Bedienungsanleitung Spirit XT485 2011-2012 (Seite 18 von 20) (Englisch)

583956

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Treadmill

XT485

Treadmill

XT485

1. Tether cord not in position.

2. Circuit breaker on front grill tripped.

Push circuit breaker in until it locks.

3. Plug is disconnected. Make sure plug is rmly pushed

into 115 VAC wall outlet.

4. Breaker panel circuit breaker may be tripped.

5. Treadmill defect. Contact your Spirit Fitness dealer.

Display does not light

Tread-belt does not stay centered

Treadmill belt hesitates when

walked/run on

The user may be walking while favoring or putting more

weight on either the left or right foot. If this

walking pattern is natural, track the belt slightly

off-center to the side opposite from the belt

movement. See General Maintenance section on

Tread-belt Tension. Adjust as necessary.

1. If the belt moves, but stops after a short time and

thedisplay shows “LS”, run calibration.

2. If you press start and the belt never moves, then the

display shows LS, contact service.

Motor is not responsive after press-

ing start

Treadmill will only achieve

approximately 7 mph but shows higher

speed on display

This indicates motor should be receiving power to

operate. Low AC voltage to treadmill. Do not use an

extension cord. If an extension cord is required it should

be as short as possible and heavy duty 16 gauge

minimum. Low voltage. Contact an electrician or your

Spirit Fitness dealer. A minimum of 110 volt AC current

is required.

High belt/deck friction. See General Maintenance

section on cleaning the deck. If cleaning doesn’t prevent

this from reoccurring, check to see if there is signicant

wear of the deck. If so, the deck may need to be ipped if

it is on its original side

Tread-belt stops quickly/suddenly when

tether cord is pulled

High belt/deck friction. See General Maintenance. If

cleaning doesn’t prevent this from reoccurring, check the

amp draw of the motor. If this is high and there are signs

of signicant wear of the deck, it may need to be ipped if

it is on its original side

Treadmill trips on board 15 amp circuit

Treadmill may not be grounded. Static electricity is

“crashing” the computer. Refer to Grounding

Instructions on page 3.

Computer shuts off when console is

touched (on a cold day) while

walking/running

Need to replace the breaker with a “High In-rush current”

type breaker (see page 3 for details)

Circuit breaker trips, but not the

treadmill circuit breaker

Service Checklist - Diagnosis Guide

Do not lubricate with other than Spirit Fitness approved lubricant.

Your treadmill comes with one tube of lubricant and extra tubes can

be ordered directly from Spirit Fitness or your authorized Spirit Fitness

dealer.

Keeping the deck lubricated at the recommended intervals ensures

the longest life possible for your treadmill. If the lubricant dries out, the

friction between the belt and deck rises and places undue stress on

the drive motor, drive belt and electronic motor control board, which

could result in catastrophic failure of these expensive components. Failure to lubricate the deck at regular

intervals may void the warranty.

The belt & deck come pre-lubricated and subsequent lubrication should be performed every 180 hours

of use. The console has a built in lubrication reminder indicator that lights every 180 hours of use.

Use the lubricant to lubricate the deck beneath the belt. If you can reach under the belt approximately

6” on each side, use the following procedure: Unplug the electrical cord. At the middle of the deck, lift up

on the belt and reach under with the tube of lubricant. Squirt most of the lubricant on the deck surface.

Repeat the process on the opposite side. Plug the electrical cord back into the outlet and walk on the belt

at a moderate speed for ve minutes.

If unable to perform the above procedure, it will be necessary to loosen the walking belt. Using the 6

mm Allen wrench supplied, loosen the two rear roller adjustment bolts -- located in the rear end caps –

enough to get your hand under the belt (5 –10 turns). Make sure to loosen both bolts the same amount

of turns and also remember how many turns, because when nished you will need to tighten the bolts

back to the point they were before.

Once the belt is loose, wipe the deck with a clean lint free cloth to remove any dirt. Apply the whole

tube of lubricant onto the deck surface about 18 inches from the motor cover. Squeeze out the contents

of the tube across the deck (parallel to the motor cover) in about a one-foot line, like toothpaste on a

toothbrush. The one-foot line should be in the middle of the deck at approximately equal distance from

both side edges of the belt. You want the lubricant to be applied about the spot that your feet would hit

the belt as you are walking. This should be about 18 inches from the motor cover, but you may want to

walk on the treadmill before loosening the belt to note where your feet land on the belt. If you mostly use

the treadmill for running, the spot where your feet land may be different from walking.

Once the lubricant is applied, tighten the rear roller bolts the same amount of turns as when you

loosened them. Run the treadmill at about 3 mph without walking on it for about a minute or two to

make sure the belt stays in the middle of the deck. If the belt tracks to one side then follow the belt

tracking instructions to remedy. Now the deck is lubricated and you should walk, not run, on the treadmill

immediately for at least 5 minutes to ensure the lubricant is evenly distributed.

Belt/Deck Lubrication Procedure

Problem Solution/Cause

Spirit XT485 2011-2012 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info