Bedienungsanleitung Spypoint Tiny-WBF (Seite 9 von 45) (Englisch)

569575

Zoom out

Zoom in

Vorherige Seite

1/45

Nächste Seite

Power • Camera

The battery level is shown in the REPORT mode (4/4 = full, 1/4= low) and

in the bottom right corner of the screen when the camera is in TEST mode.

When the battery level shows 2/4 or when a single line remains (see gure

below), the camera will continue to take photos but we strongly recommend

changing the batteries before they are empty. If a video is being recorded

and the batteries level reaches 0%, the camera saves the le before shut-

ting down.

AA BATTERIES

This camera requires 6 AA batteries (1.5V). The use of alkaline or lithium

batteries is strongly recommended. During the installation of the AA

batteries, slide the battery switch to ALK (i.e. alkaline). Insert the batteries

in the removable battery holder as indicated and insert it inside the camera

(see gure below). Battery polarity must be followed.

Please note that the voltage of rechargeable AA batteries (1.2V) is

insufcient to power the SPYPOINT

camera. We also recommend the

use of new batteries to ensure maximum performance of the camera.

LITHIUM BATTERY PACK

This SPYPOINT

camera can be powered by a rechargeable lithium battery

pack LIT-09/LIT-C-8 (sold separately, p.34). This type of battery is less

affected by cold temperatures and lasts up to 3 times longer than an alka-

line batteries. During the installation of the lithium battery pack, slide the

battery switch to RECH. Insert the battery in the removable battery holder

and insert it inside the camera (see gures above).

EXTERNAL (12V)

This camera can also be powered by an external 12-volt DC input such as

a 12-volt battery (KIT-12V, BATT-12V or KIT6V/12V) or a 12-volt adapter

(AD-12V), each sold separately (p.34). During the installation of a 12-volt

connection, slide the battery switch to ALK (the AA batteries can remain

safely inside the camera). If combined with a lithium battery pack, slide the

battery switch to RECH. For available accessories, see p.34.

SOLAR PANEL

This camera also offers the possibility to connect a solar panel (SP-12V sold

separately, p.34) to maintain the charge of the lithium battery pack

(sold separately, p.34). While installing the rechargeable lithium battery

pack, slide the battery switch to RECH to activate the charging system of

the solar panel.

Battery switch position (depending on the power source)

Power source Battery switch position

• 6AA

• 12V

• 12V + 6AA

ALK

• LIT-09*

• 12V + LIT-09*

• Solar panel + LIT-09*

RECH

* Rechargeable lithium battery pack, sold separately (LIT-09) or with a

charger (LIT-C-8).

TIME BATTERY

The camera has a CR2032 lithium button battery which saves the time and

date. To replace the battery:

1. Turn off the camera and remove it from the housing.

2. Using a at screwdriver, push the tab to the left.

3. While pushing the tab to the left, remove the compartment of the camera.

4. Replace the battery, the polarity must be respected (side + facing up).

Insert connectors

rst

6 alkaline AA batteries

Lithium battery pack

LIT-09/LIT-C-8

Connectors Connectors

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Spypoint Tiny-WBF Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Spypoint Tiny-WBF

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info