Bedienungsanleitung Stagg MOB 20 (Seite 1 von 2) (Englisch)

644333

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

FRONT PANEL:

1. (Mic) INPUT: This is a balanced XLR input for connecting a dynamic microphone. This can be a vocal mic

to sing into while you play, or alternatively an instrument mic to amplify an all-acoustic instrument that does not

feature an onboard preamp system. You may also use this input to connect an electro-acoustic instrument with

a balanced output signal.

2. (Mic) LEVEL: This control determines the output level of the sound picked up by a microphone, if one is used.

3. (Instrument) INPUT: This is a 1/4” (Ø 6.3 mm) input jack socket for plugging in an electro-acoustic

instrument. We recommend that you always use a high-quality shielded guitar cable to prevent any background

noise interference or unwanted feedback.

4. (Instrument) LEVEL: This control determines the output level of any instrument plugged into the amplier

via the instrument input jack.

5. PASSIVE/ACTIVE SWITCH: This switch enables the user to choose between passive and active modes

according to whether the instrument connected is passive (without preamp) or active (with preamp).

6. TREBLE: This control determines the level of high frequencies in the output signal. Adding TREBLE will make

your sound brighter and sharper.

7. MID: This control determines the level of middle frequencies in the output signal. Adding MID will make your

sound rounder and fuller.

8. PARAMETRIC MID: This control allows you to ne tune your sound by cutting or boosting the mid frequency

parameters of the output signal. At a low level, the PARAMETRIC MID control will emphasize the lower mids,

while increasing the level will bring out the upper mids. The PARAMETRIC MID control can help you explore a

wide variety of different guitar tones.

9. BASS: This control determines the level of low frequencies in the output signal. Adding BASS will make your

sound warmer and heavier.

10. SPRING REVERB: This is the reverb intensity control. This controls the amount of reverb that is added

back to the original dry signal. Adding REVERB will produce a reverberation effect in your instrument sound, as

though you were playing in a large hall. A little can go a long way in adding that special depth to your sound. If

engaged, the reverb is always active in both microphone and instrument channels.

11. CD/MP3 INPUT (L + R): These are line level, RCA phone sockets (Right + Left) into which a stereo MP3/

CD/Tape player may be connected.

12. PHONES: This is a 1/4” (Ø 6.3 mm) stereo jack output to connect the headphones. When headphones are

connected, no sound is produced from the speaker.

13. POWER LED: When this red LED is lit, the amplier is ready to work. When it is off, it means the amplier

is powered off.

BACK PANEL:

1 DC 12V/ 800mA INPUT: This is the input socket into which the 12V DC cable of a mains power adaptor can

be plugged if you wish to recharge the built in 12V DC battery, or power your amplier from the mains network.

CAUTION: Use only the included AC adaptor to avoid damaging the amplier or generating any other problems.

Please check that the supply voltage details mentioned on the mains power adaptor are in accordance with your

electricity supply.

2 POWER SWITCH: This switch turns the amplier on or off, either on battery operation or with the amplier

connected to the proper AC outlet through the mains adaptor (included).

TECHNICAL SPECIFICATIONS

Max. Rated Power Loudspeaker 12 Watts RMS @ 4 Ohms load/ 6.5" Twin Cone Speaker

Frequency Response 65 Hz to 18 kHz

Total Harmonic Distortion 3.5 %

Signal to Noise Ratio -64 dB @ max Rated Power

Input Impedance

180k Ohms

Power Consumption

22 Watts Max (w/ fully charged battery)

Maximum Input Level

56 mV (RMS)

Maximum Gain

60 dB (@ 1kHz)

Dimensions (H x W x D)

37 x 40.5 x 20 cm / 14.6 x 16 x 7.9 in.

Weight

9.2 kg / 20.3 lbs

BATTERY SPECIFICATIONS

Type FP 1223, 12V 2.3 Ah/ 20Hr, rechargeable lead battery

Size (L x W x H) 176 x 35 x 61 mm / 7.01 x 1.38 x 2.40 in

Weight (approx) 970 g / 2.13 lbs

POWER ADAPTOR SPECIFICATIONS

Type

AC 230 – 240 V/ 100 mA to DC 12 V/ 800 mA/ 9.6 VA

Transformer

Size (L x W x H) 81 x 56 x 49 mm / 3.19 x 2.20 x 1.93 in

Weight (approx) 500 g / 1.10 lbs

Features and Specications are subject to change without notice.

INSTRUCTIONS FOR USE:

Connect your instrument to the input socket of the amplier with a suitable guitar lead (this lead is not supplied

with the amplier, but is normally supplied with the instrument). You may also plug a microphone into the XLR

input provided. If connecting a microphone, please ensure that the volume level is set low before turning on

the amplier, as feedback can otherwise result, possibly causing damage to the speaker. Finally, press the Power

Switch to the ON position. The power LED will glow and your amplier is ready for use.

WARNING: This amplier works on both battery and AC outlet. When using the built in, rechargeable 12V

DC BATTERY only, the unit can function for about 15 hours of continuous use (expected), depending on the

actual operating conditions. When using the AC adaptor, operation will continue in the event of AC line voltage

interruption (power blackout or power plug disconnection) thanks to the battery mounted in the unit.

13121110

987654321

Stagg MOB 20 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Stagg MOB 20

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info