Bedienungsanleitung Standard Horizon CP390i - GPS Chart Plotter (Seite 113 von 168) (Englisch)

603481

113

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

Page 114 CP390i and CPF390i

13.3 ALARMS

The Alarms menu is used to select and setup audible and visual Alarms. Available alarms

are Arrival, XTE, Depth, Anchor and Grounding Alarm.

Arrival Alarm : Alerts when the vessel is approaching a single destination point or when arriving at a leg

in a Route. Available selections: 0.00 to 9.99NM.

XTE Alarm : Alerts when the vessel is deviating from a defined course. Available selections: 0.00 to

9.99NM.

Depth Alarm : Alerts when the received depth Value is lower than the selected value. Available selections:

0000 to 3000FT.

Anchor Alarm : Alerts when the ships moves off a selected locations by a selected distance. Available

selections: 0.00 to 9.99NM.

Audble Alarm : Enables or disables the alarm beep.

Grounding Alarm : This function looks ahead of the vessels heading to see if a potential danger exists. When

the Grounding Alarm is enabled the GPS Chart Plotter will draw a triangle in front of the vessel

on the Chart page showing the area that is being searched as shown below. The depth and

range (distance) of the area the GPS Chart Plotter looks ahead for a shallow area can be set

using this function.

Grounding Alarm Range : This function allows setting the distance of the grounding alarm zone (the length of the sector

to be detected) among the 0.25, 0.5, 1.0 Nm selections. When a depth or any of the searched

objects is found in the scanned area, a tick marker is printed on the relative box in the Grounding

Alarm Report page to identify which dangerous objects have been currently detected.

Grounding Alarm Report: This function allows displaying a report of the dangerous objects currently detected.

The following warning appears when the Grounding Alarm is enabled.

NOTES

The Grounding Alarm function is available only if a NT

/MAX C-CARD is inserted. It also affects the

screen redraw speed so we suggest to disable it when not used.

When any of the objects checked are found for the first time, the GPS Chart Plotter shows a pop

up window to alert the user of the possible danger. The name of each new dangerous object found

is reported in the warning window. In the Grounding Alarm Report page the relative item has a tick

marker next to it, to identify the dangerous object currently detected. If in the next search cycle the

same objects are found again, the alarm window will not be shown. Instead, if in the next searches

the objects found before are no longer detected, their relevant item in the Grounding Alarm Report

page is cleared (note that in this case, if the same object type is found again later, the Alarm will

be shown). The GPS Chart Plotter shows an icon on the charts that identifies when a Grounding

Alarm is detected.

Figure 13.3 - Grounding Alarm

13.4 SIMULATION

The built-in Simulator function allows you to become proficient in the use of the GPS Chart

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Standard Horizon CP390i - GPS Chart Plotter Seite 113

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info