603509
21
Zoom out
Zoom in
Vorherige Seite
1/166
Nächste Seite
CPF180i and CPF300i Page 23
CPF180i
Battery
10-35Vdc
Red
2A
Fuse
Black
Switch
+
-
VHF
PILOT
Green
Blue
Brown
NMEA Common
Port 1 Input
Port 1Output
Yellow Port 3Output
PWR & ACC 1 Cable
Transducer
Optional WAAS GPS
antenna
2.4.1.2 AIS Setup
The CPF180i has to be set up to be able to receive NMEA information from the AIS receiver.
The GPS Chart Plotter reads the AIS NMEA message VMD, type 1, 2, 3 and 5 for AIS Class
A and type 18, 19, 24 for AIS Class B. Select the used port and transmission speed by
following the procedure:
1. Press [MENU], move the ShuttlePoint knob to highlight
SETUP MENU and press [ENT].
2. Move the ShuttlePoint knob to highlight
ADVANCED SETUP and press [ENT] or move
the ShuttlePoint knob to the right.
3. Move the ShuttlePoint knob to highlight
IN/OUT CONNECTIONS and press [ENT] or
move the ShuttlePoint knob to the right.
4. Move the ShuttlePoint knob to highlight
PORT1 INPUT and press [ENT] or move the
ShuttlePoint knob to the right.
5. Move the ShuttlePoint knob up/down to select
AIS 38400 and press [ENT] or move the
ShuttlePoint knob to the right.
NOTE
If an AIS receiver is not connected, Port1 Input can be connected to most DSC VHF’s for position polling.
NOTE
The Input and Output baud rate for each port is set using the Advanced Setup>In/Out Connections
menu. For example if Port1 is set for AIS 38400, the Input and Output both operate at 38400 baud.
2.4.2 CPF300i Connection Table
12VDC Power
Pin Wire Color Description Connection Example Additional Comments
1 Black Battery Ground &
Connect to Battery Ground and
Common for and signal ground
NMEA devices*
2 Red Battery Positive Connect to Battery Positive
3 Green Port3 Input Connect to Output of NMEA devices* Default is NMEA0183
4 Blue Port1 Input Connect to Output of NMEA devices* Default is NMEA0183
5 Brown Port1 Output Connect to Input of NMEA devices* Default is NMEA0183 with GGA, GLL, RMC,
XTE, DBT, DPT, MTW, VHW sentences
6 Gray Port2 Input Connect to Output of NMEA devices* Default is NMEA0183
7 White Port2 Output Connect to Input of NMEA devices* Default is NMEA0183 with GGA, GLL, RMC
and XTE sentences
8 Yellow Port3 Output Connect to Input of NMEA devices* Default is NMEA0183 with APA, APB, BOD,
GGA, GLL, RMC and BOD sentences
21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Standard Horizon CPF300i wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info