Bedienungsanleitung Standard Horizon CPF390i - GPS Chart Plotter-Fish Finder (Seite 18 von 168) (Englisch)

603482

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

CP390i and CPF390i Page 19

1. After a location is found, peel the template label from the backing and apply the label

to the mounting area.

2. Drill a hole in one area of the cutout area that will allow the blade of a jig saw to be

inserted. Insert and cut out the area on the panel using the jig saw.

3. Next drill the four holes required to insert the GPS Chart Plotter with the mounting studs.

4. Install the mounting studs on the GPS Chart Plotter and insert into the mounting hole.

5. Attach the GPS Chart Plotter to the mounting location by attaching the supplied

hardware to the mounting studs.

2.3 MOUNTING THE OPTIONAL EXTERNAL GPS ANTENNA

An external WAAS GPS antenna is available when the CP390i and CPF390i is flush

mounted or mounted in an area where satellite reception is not possible with the internal

antenna.This antenna is designed to be mounted on a base, installed on an extension or

flush mounted.

Choose a location for the antenna that has a clear view of the sky and is not located within

3Feet of a Radar or other transmitting antennas. Ensure there are no major obstructions or

fixtures in the immediate proximity to the antenna. The antenna relies on direct “line of sight”

satellite reception. If you are unsure of the chosen location, temporarily mount the antenna

in the desired location to verify correct operation. If mounted close to Radar, after the GPS

Chart Plotter has a fix, turn on the Radar to ensure the GPS Chart Plotter holds the fix (use

the GPS Status Page).

The thread used on the antenna is an industry standard (1inch 14TPI) used on a wide range

of mounting brackets.

NOTE

The antenna cable can be cut and spliced to ease installation. Care must be taken when

reconnecting the antenna cable to protect from water and corrosion.

2.3.0 Flush mounting the antenna

NOTE

Before drilling holes, it is recommended the antenna be positioned where the location is planned,

cable connected to the GPS Chart Plotter and power turned on to ensure a GPS Fix is received.

1. Remove the threaded base from the antenna dome.

2. To ease installation a flush mounting template for the antenna has been included.

3. Apply the mounting template sticker to the area that was verified for GPS reception.

4. Then, drill out the 0.78” (20mm) and 0.13” (3.2mm) holes, and remove the template.

5. Insert the cable into the 0.78” (20mm) hole and route to the GPS Chart Plotter.

6. Apply a small amount or RTV to the underside of the antenna.

7. Place the antenna and then screw it into place using the screws.

NOTE

In some cases the screw may not be long enough. If this happens simply apply more RTV to the

underside of the antenna to glue it into place.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Standard Horizon CPF390i - GPS Chart Plotter-Fish Finder Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info