603490

Standard Horizon RAM 3 - CMP30 Seite 2

2
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
RAM3
(
CMP30
)
CONTROLS
[
H/L
]
Key
Press this key to toggle the transmit power between high
and low. When the
[
H/L
]
key is pressed while the trans-
ceiver is on channel 13 or 67, the power will temporarily
switch from LOW to HI power until the PTT is released.
The
[
H/L
]
key does not function on transmit inhibited and
low power only channels.
PTT
(
Push-To-Talk
)
Key
Press this key to activate the transmission.
POWER
(
)
Key
Press and hold down this key to turn to the transceiver
and RAM3
(
CMP30
)
“on” and “off”.
Microphone
The internal microphone is located here.
When transmitting, position your mouth about 1/2 to 1 inch
(1.2 ~ 2.5 cm) away from the small mic hole. Speak slowly
and clearly into the microphone.
DISPLAY
Channel display.
SOFT KEY
For details, refer to “Mode Setting and Setup” above.
KEY PAD
[
CALL/MENU
]
Key
Press this key to access the DSC OPERATION menu.
Press and hold this key to access the SETUP menu.
[
16/9
]
Key
First press: channel 16 is immediately selected.
Second press: recalls the last selected channel.
Press and hold: selects channel 9.
[
S
](
UP
)
/
[
T
](
DOWN
)
Key
These keys are used to select channels, adjust the vol-
ume and squelch level, and to choose DSC calls, DSC
setup and Radio setup function.
[
VOL/SQ
]
Key
(
Volume Control / Squelch Control
)
Press this key to toggle the function of the microphone’s
[
S
]
or
[
T
]
key between the channel selections, volume
level adjustment, and squelch level adjustment.
[
CLR/WX
]
Key
For details, refer to “Mode Setting and Setup” above.
[
ENT
]
Key
This key functions as the enter key.
Speaker
The internal speaker is located here.
[
DISTRESS
]
KEY
This key is used to send a DSC Distress Call.
Lift the red spring loaded DISTRESS cover, then press
and hold in the
[
DISTRESS
]
key.
MODE SETTING & SETUP
The RAM3
(
CMP30
)
is backward compatible Standard Horizon VHF radios that use the RAM+
(
CMP25
)
and VH-310
(
telephone style handset
)
.
MODE SELECTION
The Mode selection allows the RAM3
(
CMP30
)
to be setup to
operate with specific models, refer to the section below for
compatibility.
Mode 1: GX1256S, GX1280S, and GX2360S
Mode 2: PS1000, PS2000, CPV350, CPV550, GX1500S/E,
GX3000S/E, GX3500S
Ú
, GX5000S, GX5500S,
and VM-3500E
Ú
Ú To use Mode 2 on the GX3500S or VM-3500E the radio
software may have to be updated. Please contact Stan-
dard Horizon for details.
1. Turn the RAM3
(
CMP30
)
off, press
and hold the
[
ENT
]
key then press
and hold the orange POWER
(
)
key until the menu is shown.
2. Press the
[
S
]
or
[
T
]
key to select
“
Operation ModeOperation Mode
Operation ModeOperation Mode
Operation Mode” item, then press
the
[
ENT
]
key.
3. Press the
[
S
]
or
[
T
]
key to select the Operation Mode
(“
Mode 1Mode 1
Mode 1Mode 1
Mode 1” or “
Mode 2Mode 2
Mode 2Mode 2
Mode 2”) and press the
[
ENT
]
key.
4. Press the
[
T
]
key to select “
Save &Save &
Save &Save &
Save &
ExitExit
ExitExit
Exit” and press the
[
ENT
]
key.
KEY SETUP
The following are used only when Mode 2 is selected
and the RAM3
(
CMP30
)
is connected to a compatible
radio.
[
CLR/WX
]
Function:
The operation of this key may be changed to select WX chan-
nels for North American market or CLR for Europe. By default
the when the key is pressed, the last selected WX channel
will be shown.
1. To change this key to operate the
CLR function, Turn the RAM3
(
CMP30
)
off, press and hold the
[
ENT
]
key then press and hold the
orange POWER
(
)
key until the
menu is shown.
2. Press the
[
T
]
key to select “
[
CLRCLR
CLRCLR
CLR/
WXWX
WXWX
WX
]
Function Function
Function Function
Function” and press the
[
ENT
]
key.
3. Select “
CLRCLR
CLRCLR
CLR” and press the
[
ENT
]
key.
4. Press the
[
T
]
key to select “
Save &Save &
Save &Save &
Save &
ExitExit
ExitExit
Exit” and press the
[
ENT
]
key.
Define
[
Soft
]
Keys:
By default the soft keys are assigned as SCAN, DW and NAV,
however these keys can be changed. In addition the soft keys
can be increased / assigned, refer below:
1. Turn the RAM3
(
CMP30
)
off, press
and hold the
[
ENT
]
key then press
and hold the orange POWER
(
)
key until the menu is shown.
2. Press the
[
T
]
key to select “
DefineDefine
DefineDefine
Define
[
SoftSoft
SoftSoft
Soft
]
keys keys
keys keys
keys” and press the
[
ENT
]
key.
3. Press the
[
S
]
or
[
T
]
key to select
the
[
Soft
]
key, and press the
[
ENT
]
key. Then, press the
[
S
]
or
[
T
]
key
to select the new function to be
assigned, and press the
[
ENT
]
key.
Available functions are listed below.
4. Press the
[
CLR/WX
]
key to return
to the “Soft Key Setup” mode.
5. Press the
[
T
]
key to select “
Save &Save &
Save &Save &
Save &
ExitExit
ExitExit
Exit” and press the
[
ENT
]
key.
Number of Soft Keys:
3 soft keys are set as default. However the RAM3
(
CMP30
)
allows assigning of up to 10 soft keys with the instructions
below:
1. Turn the RAM3
(
CMP30
)
off, press
and hold the
[
ENT
]
key then press
and hold the orange POWER
(
)
key until the menu is shown.
2. Press the
[
T
]
key to select “
Num-Num-
Num-Num-
Num-
ber of Soft keysber of Soft keys
ber of Soft keysber of Soft keys
ber of Soft keys” and press the
[
ENT
]
key.
3. Select the number of soft keys (3,
4, 6, 8 or 10) and press the
[
ENT
]
key.
4. Press the
[
T
]
key to select “
Save &Save &
Save &Save &
Save &
ExitExit
ExitExit
Exit” and press the
[
ENT
]
key.
IMPORTANT NOTE
Mode 2 only allows the RAM3
(
CMP30
)
to define the
[
CLR/WX
]
key and assign / Change the number of se-
lectable soft keys.
DISPLAY
SCAN
DW
NAV
DIM
MEM
IC
PA
FOG
SCRM
WX
CLR
FUNCTION
Ú
Stops and starts scanning.
Stops and starts Dual Watch Scan.
Displays the GPS Navigation Data.
Enables the LCD backlight dimmer function.
When pressed memorizes a channel for scanning.
Activates the Intercom function.
Operates the PA function.
Operates the Fog Horn function.
Toggles the Voice Scrambler “on” and “off”.
Immediately recalls the previously selected US
NOAA weather channel.
Cancels the menu selection.
Ú: Some functions may not operate depending on the connected radio.
OPTIONAL ACCESSORIES
CT-100 23FT EXTENSION CABLE
MLS-310 10 WATT AMPLIFIED SPEAKER
MLS-300 EXTERNAL LOUD SPEAKER
LCD SETTING
The RAM3
(
CMP30
)
has the capability to change the LCD
contrast by following the instructions below.
1. Press and hold down the
[
CALL/MENU
]
key until “
RADIORADIO
RADIORADIO
RADIO
SETUPSETUP
SETUPSETUP
SETUP” menu appears.
2. Press the
[
CALL/MENU
]
key, then
press the
[
T
]
key until the “
CON-CON-
CON-CON-
CON-
TRASTTRAST
TRASTTRAST
TRAST” menu appears.
3. Press the
[
CALL/MENU
]
key again,
then press the
[
S
]
or
[
T
]
key to se-
lect the desired contrast level.
4. Press the
[
CALL/MENU
]
key to
store the selected level, then press
the
[
16/9
]
key to exit “
RADIO SETUPRADIO SETUP
RADIO SETUPRADIO SETUP
RADIO SETUP”
menu and return to radio operation
mode.
SPECIFICATIONS
Supply voltage: 13.8 VDC (Supplied from the transceiver)
Current consumption: 700 mA @VOL Max.
200 mA @AF Mute
Operating Temperature: –4 °F to +140 °F (–20 °C to +60 °C)
MIC. Sensitivity (Typical): 60 mVrms
@ 1 kHz Tone with 3 kHz Deviation
MIC. Impedance:2 kΩ
AF output: 300 mW @ 16 Ω for 10 % THD
(Internal Speaker)
2 W @ 4 Ω for 10 % THD
(External Speaker)
Display Size: 1.8” x 0.9” (45 x 23 mm)
Display Resolution: 132 x 64 dot
Case Size: 2.6” x 5.5” x 1.2” (67 x 140 x 30 mm)
Weight (Approx): 11.6 oz (330g)
2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Standard Horizon RAM 3 - CMP30 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info