Bedienungsanleitung Stanley 42-063 (Seite 2 von 17) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

720392

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

42-063 / 42-065 / 42-086

Digital Level

OPERATING INSTRUCTIONS

Installing Batteries: See

The battery compartment is located on back of level.

1. Push in on tab and lift cover.

2. Insert (2) AAA batteries as shown.

3. Replace cover & snap in place.

Features: See

1. Plumb Vial

2. Calibration Button

3. Reference Button

4. Unit Button

5. Power Button

6. Hold Button

7. Buzzer/ Backlight Button

8. Level Vial

Display: See

9. Slope Icon

10. Buzzer Icon

11. Hold indicator

12. Ref Indicator

13. Battery life icon

14. Unit icons

Power:

Press Power button

for ~1 sec. to turn on display.

• When powering on, the inclination will be displayed in the

last units selected.

• The slope direction is shown by the slope icon

• The display will automatically power off after 5 minutes of

non-use.

• The display will automatically flip over if the level is used

inverted.

• The battery life icon

displays the power remaining in the

batteries. When Battery life icon is as shown, , there is

~ 1 hour of battery life remaining.

Units:

Press the units button

for ~1 sec. to cycle the display units

between degrees (°), slope (mm/m) or gradient (%).

Hold:

Press the Hold button

to freeze the current angle shown on

the display. Press

again to unfreeze the displayed angle.

Buzzer/Backlight:

Press the Buzzer/Backlight button

for ~1 sec. to activate the

internal buzzer. The buzzer will be heard when the display is at

0, 45 or 90°. Press the button again to ~1 sec. to power off the

buzzer.

Press the Buzzer/Backlight button

for >2 sec. to activate to

display backlight. The backlight will automatically power off after

5 minutes or the button can be pressed again for >2 sec.

Reference Angle:

Press the Reference button

for >2 sec. to reset to current

inclination to 0°. Press the Reference button again to return to

normal angle mode.

Temperature:

Press the Calibrate button

for ~1 sec. to display the current

temperature in °C. Press again for ~1 sec. to display in °F. Press

again to return to normal angle mode.

Re-calibrating the zero set angle of the display:

If the unit is dropped or you suspect inaccuracy of the product,

you can re-calibrate the zero point.

1. Place the level on a flat, level surface as shown below.

2. Press the calibration button

for >4 sec. “CAL 1” will

appear on the display.

3. Press the calibration button

for ~1 sec. “CAL 1” will blink

for ~1 sec. then change to “CAL 2”.

4. Flip the level over so the bottom is now on top, as shown

below.

5. Press the calibration button for ~1 sec. “CAL 2” will blink for

~1 sec. then change to the active angle display.

The 0° reference for the display has been re-calibrated to the

level surface.

SPECIFICATIONS

Power: 3VDC (2) AAA Batteries

(included)

(Alkaline recommended)

Measuring Range:

0-360° (0-90° quadrants)

Digital Angle accuracy:

±0.1° @ level and plumb

±0.2° 1° to 89°

Vial(s) Accuracy:

0.057° (1.0mm/m)

Operating Temperature:

0° to 50°C (32° to 122°F)

Storage Temperature:

-20° to 70°C (-4° to 158°F)

Battery life: ~20 Hrs (w/ backlight)

Shock Resistance:

Up to 1m (3 feet) drop on concrete

Water Resistance:

Water resistant, but not waterproof

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley 42-063 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info