Retain all sections of the manual for future reference.
User Safety
WARNING:
• Carefully read the Safety Instructions and Product Manual
before using this product. The person responsible for the
instrument must ensure that all users understand and adhere to
these instructions.
WARNING:
• The following labels are placed on the laser tool to inform you of
the laser class for your convenience and safety
translated here for your convenience)
IEC /EN 60825-1
Complies with 21 CFR 1040.10 and 1040.11 except for deviations
pursuant to Laser Notice No. 50, dated June 2007
CAUTION:
• While the laser tool is in operation, be careful not to expose your
eyes to the emitting laser beam (red light source). Exposure to a
laser beam for an extended time may be hazardous to your eyes.
CAUTION:
• Glasses may be supplied in some of the laser tool kits. These are
NOT certified safety glasses. These glasses are ONL
enhance the visibility of the beam in brighter environments or at
greater distances from laser source.
Contents
• User Safety
• Contents
• Product Overview
• Keypad, Modes, and LED
• Applications
• Batteries and Power
• Set Up
• Operation
• Accuracy Check and Calibration
• Specifications
Product Overview
Figure A - Laser T
1. Power /T
2. Laser Window
3. Keypad
4. 1/4-20 threaded mount
5. 5/8-11 threaded mount
6. Battery Cover with Warning label
7. 4 x AA Batteries
Figure B - Power /T
Figure C - Laser Modes
Figure D - Keypad
Figure H - Level Beam Accuracy
Figure I - Horizontal Beam Accuracy
Figure J - Vertical Beam Accuracy
Keypad, Modes, and LED
Switch
Power ON/Pendulum lock off /Self-leveling On
Power OFF/Pendulum lock on
•T move switch to the unlocked position
•T
Modes
Laser Beam Available Modes
•AllbeamlinesON
•AllbeamlinesOFF
Self-Leveling (See figure
B
)
•
ON position to enable self-leveling.
Keypad-Pulse key.
Pulse mode ON/OFF key (See figure
D
)
Press to activate Pulse mode.(See figure
D
# 10 )
Pulse Mode LED/Out-of-Level Indicator Operation (See figure
D
# 9 )
LED OFF
1. Pulse Mode is OFF/ Unit is level
LED ON-CONTINUOUS
2. PULSE MODE is ON, and laser unit is within self-leveling range
LED ON-FLASHING
3. Laser unit is OUT OF LEVEL.
Keypad-Battery key
Battery level indicator key (See figure
D
)
Battery Life LED (See figure
D
# 8)
LED OFF
1. Battery life >25%
LED
2. Battery life < 25%
Applications
Plumb T
•Usingtheverticallaserbeam,establishaverticalreferenceplane.
•
planetoensureobject(s)areplumb.
Level T
•Usingthehorizontallaserbeam,establishahorizontalreferenceplane.
•
referenceplanetoensureobject(s)arelevel.
Square
• Using the vertical and horizontal laser beams, establish a point where the two
beams cross.
•
horizontallaserbeamstoensureobjects(s)aresquare.
Batteries and Power
Battery Installation / Removal (See figure
B
)
Laser T
• T
• Install / Remove batteries. Orient batteries correctly when placing into
battery compartment.
• Close battery door
WARNING:
• Pay close attention to the battery holder’
for proper battery insertion. Batteries must be of same type and
capacity
capacities remaining.
Set Up
Laser T
• Place laser tool on a flat, stable surface.
• T
/ transport lock to the unlocked position. The laser tool must then be
positioned in its upright position on a surface that is within the specified
compensation range.
Mounting on Accessories
• Position accessory in a place where it will not be easily disturbed and
near the central location of the area to be measured.
• Setuptheaccessoryasrequired.Adjustpositioningtobesureaccessory
base is near horizontal (within laser tools compensation range).
• Mount the laser tool to the accessory using the appropriate fastening
method to be used with such accessory / laser tool combination.
CAUTION:
• Do not leave the laser tool unattended on an accessory without
fully tightening the fastening screw
the laser tool falling and sustaining possible damage.
NOTE:
• It is best practice to always support laser tool with one hand when placing or
removing laser tool from an accessory
• If positioning over a target, partially tighten the fastener
and then fully tighten.
Operation
NOTE:
• Before operating the laser tool always be sure to check the laser tool for
accuracy
• Laser tool will indicate when it is out of compensation range. Reference LED
Descriptions. Reposition laser tool to be closer to level.
• When not in use, please be sure to power OFF the laser tool by placeing the
pendulum lock in the locked position.
Power
• T
position.
• T
position.
Modes
OFF/ Locked (See figures
B
)
•
The laser will be OFF and the pendulum locked.
ON/ Self-Leveling (See figures
B
)
•
The pendulum lock on the laser tool will be positioned in the unlocked
/self-leveling position when the laser is turned ON
•
Accuracy Check and Calibration
NOTE:
• The laser tools are sealed and calibrated at the factory to the accuracies
specified.
• It is recommended to perform a calibration check prior to its first use and
then periodically during future use.
• The laser tool should be checked regularly to ensure its accuracies,
especially for precise layouts.
• When performing the accuracy checks, use the largest area / distance
possible, closest to the operating distance. The greater the area / distance,
the easier to measure the accuracy of the laser
• The lock must be in the unlocked position to allow the laser tool to self-level
before checking the accuracy
Level Beam Accuracy (See figure
H
)
•
H
1
Place laser tool as shown with laser ON. Mark point P
1
at cross.
•
H
2
Rotate laser tool 180° and mark point P
2
at cross.
•
H
3
Move laser tool close to wall and mark point P
3
at cross.
•
H
4
Rotate laser tool 180° and mark point P
4
at cross.
•
H
5
Measure the vertical distance between P
1
and P
3
to get D
3
and the
vertical distance between P
2
and P
4
to get D
4
.
• Calculate the maximum offset distance and compare to the difference of
D
3
and D
4
asshownintheequation.
• If the sum is not less than or equal to the calculated maximum
offset distance the tool must be returned to your Stanley
Distributor for calibration.
Maximum Offset Distance:
= 0,6
mm
m
x (D
1
m - (2 x D
2
m))
Maximum
= 0,007
in
ft
x (D
1
ft - (2 x D
2
ft))
Compare : (See figure
H
5
)
D
3
- D
4
≤ ± Maximum
Example:
• D
1
= 10 m, D
2
= 0,5 m
• D
3
= 0,5 mm
• D
4
= - 1,0 mm
• 0,6
mm
m
x (10 m - (2 x 0,5 m) = 5.4 mm
(maximum offset distance)
• (0,5 mm) - (- 1,0 mm) = 1,5 mm
• 1,5 mm ≤ 5.4 mm
(TRUE, tool is within calibration)
77-348 FCL-G - GB.indd 2 19/12/2014 11:10
