Bedienungsanleitung Stanley FMC660 (Seite 6 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

622176

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

ENGLISH

(Original instructions)

c. When restarting a saw in the workpiece, centre the

saw blade in the kerf and check that saw teeth are not

engaged into the material. If saw blade is binding, it may

walk up or kickback from the workpiece as the saw is

restarted.

d. Support large panels to minimise the risk of blade

pinching and kickback. Large panels tend to sag under

their own weight. Supports must be placed under the

panel on both sides, near the line of cut and near the edge

of the panel.

e. Do not use dull or damaged blades. Unsharpened or

improperly set blades produce narrow kerf causing

excessive friction, blade binding and kickback.

f. Blade depth and bevel adjusting locking levers must

be tight and secure before making cut. If blade

adjustment shifts while cutting, it may cause binding and

kickback.

g. Use extra caution when sawing into existing walls or

other blind areas. The protruding blade may cut objects

that can cause kickback.

Lower guard function

a. Check lower guard for proper closing before each

use. Do not operate the saw if lower guard does not

move freely and close instantly. Never clamp or tie the

lower guard into the open position. If saw is

accidentally dropped, lower guard may be bent. Raise the

lower guard with the retracting handle and make sure it

moves freely and does not touch the blade or any other

part, in all angles and depths of cut.

b. Check the operation of the lower guard spring. If the

guard and the spring are not operating properly, they

must be serviced before use. Lower guard may operate

sluggishly due to damaged parts, gummy deposits, or a

build-up of debris.

c. Lower guard may be retracted manually only for

special cuts such as "plunge cuts" and "compound

cuts". Raise lower guard by retracting handle and as soon

as blade enters the material, the lower guard must be

released. For all other sawing, the lower guard should

operate automatically.

d. Always observe that the lower guard is covering the

blade before placing saw down on bench or ﬂ oor. An

unprotected, coasting blade will cause the saw to walk

backwards, cutting whatever is in its path. Be aware of the

time it takes for the blade to stop after switch is released.

Residual risks

Additional residual risks may arise when using the tool which

may not be included in the enclosed safety warnings. These

risks can arise from misuse, prolonged use etc.

Even with the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks can not be avoided. These include:

 Injuries caused by touching any rotating/moving parts.

 Injuries caused when changing any parts, blades or ac-

cessories.

 Injuries caused by prolonged use of a tool. When using

any tool for prolonged periods ensure you take regular

breaks.

 Impairment of hearing.

 Health hazards caused by breathing dust developed when

using your tool (example:- working with wood, especially

oak, beech and MDF.)

Saw blades

 Do not use blades of larger or smaller diameter than

recommended. For the proper blade rating refer to the

technical data. Use only the blades specif ed in this

manual, complying with EN 847-1.

 Warning! Never use abrasive wheels.

Safety of others

 This appliance is not intended for use by persons (includ-

ing children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concern-

ing use of the appliance by a person responsible for their

safety.

 Children should be supervised to ensure that they do not

play with the appliance.

Vibration

The declared vibration emission values stated in the technical

data and the declaration of conformity have been measured

in accordance with a standard test method provided by

EN 60745 and may be used for comparing one tool with

another. The declared vibration emission value may also be

used in a preliminary assessment of exposure.

Warning! The vibration emission value during actual use of

the power tool can differ from the declared value depending

on the ways in which the tool is used. The vibration level may

increase above the level stated.

When assessing vibration exposure to determine safety

measures required by 2002/44/EC to protect persons regularly

using power tools in employment, an estimation of vibration

exposure should consider, the actual conditions of use and the

way the tool is used, including taking account of all parts of the

operating cycle such as the times when the tool is switched off

and when it is running idle in addition to the trigger time.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley FMC660 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info