Bedienungsanleitung Stanley FMCD900 (Seite 6 von 68) (Alle Sprachen)

720429

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

ENGLISH

(Original instructions)

Chargers

u Use your Stanley FatMax charger only to charge the

battery in the tool with which it was supplied. Other

batteries could burst, causing personal injury and damage.

u Never attempt to charge non-rechargeable batteries.

u Have defective cords replaced immediately.

u Do not expose the charger to water.

u Do not open the charger.

u Do not probe the charger.

The charger is intended for indoor use only.

Read the instruction manual before use.

Electrical safety

Your charger is double insulated; therefore no

earth wire is required. Always check that the

mains voltage corresponds to the voltage on

the rating plate. Never attempt to replace the

charger unit with a regular mains plug.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Stanley FatMax Service

Centre in order to avoid a hazard

Features

This tool includes some or all of the following features.

1. On/Off switch

2. Forward/reverse selecter

3. Drilling mode selector

4. Depth stop

5. Tool holder

6. Side handle

7. Battery (Not supplied)

Assembly

Use

Warning! Let the tool work at its own pace. Do not overload.

Charging the battery (Two batteries provided with

the FMCD900M2S & FMCD900M2T units, no

batteries provided with the FMCD900B unit) (g. A)

The battery needs to be charged before rst use and

whenever it fails to produce sufcient power on jobs that were

easily done before. The battery may become warm while

charging; this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 10 °C or above 40 °C. Recommended charging

temperature: approx. 24 °C.

Note: The charger will not charge a battery if the cell

temperature is below approximately 10 °C or above 40 °C.

The battery should be left in the charger and the charger will

begin to charge automatically when the cell temperature

warms up or cools down.

u To charge the battery, insert the Battery (7) into the

charger (9). The battery will only t into the charger one

way.

u Plug the charger (9) into a suitable power source and

switch on.

u Charge discharged batteries within 1 week. Battery life will

be greatly diminished if stored in a discharged state.

Fitting and removing the battery (Two batteries

provided with the FMCD900M2S & FMCD900M2T

units, no batteries provided with the FMCD900B

unit) (g. B)

u To t the battery, line it up with the receptacle on the tool

(11). Slide the battery into the receptacle and push until

the battery snaps into place.

u To remove the battery, push the release button (12) and

remove the battery from the receptacle.

Fitting the side handle (g. C)

u Turn the grip counterclockwise until you can slide the side

handle (6) onto the front of the tool as shown.

u Rotate the side handle into the desired position.

u Tighten the side handle by turning the grip clockwise.

Fitting and setting the depth stop (g. C)

u Depress the button (8).

u Insert the depth stop (4) into the mounting hole as shown.

u Set the depth stop (4) to the desired position. The

maximum drilling depth is equal to the distance between

the tip of the drill bit and the front end of the depth stop.

u Release the button (8).

Fitting an accessory (g. D - E)

u Clean and grease the shank (13) of the accessory.

u Pull back the sleeve (14) and insert the shank into the tool

holder (5).

u Push the accessory down and turn it slightly until it ts into

the slots.

u Pull on the accessory to check if it is properly locked. The

hammering function requires the accessory to be able to

move axially several centimetres when locked in the tool

holder.

u To remove the accessory, pull back the sleeve (14) and

pull out the accessory.

Keyed chuck (g. F) (Not supplied)

u Open the chuck by turning the sleeve (15) anti-clockwise.

u Insert the bit shaft (17) into the chuck.

u Insert the chuck key (18) into each hole (16) in the side of

the chuck and turn clockwise until tight.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley FMCD900 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Stanley FMCD900

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info