Bedienungsanleitung Stanley FMCS701 (Seite 13 von 186) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

720682

Zoom out

Zoom in

Vorherige Seite

1/186

Nächste Seite

ENGLISH

(Original instructions)

Features

This tool includes some or all of the following features.

1. Trigger switch

2. Operating handle

3. Mounting holes

4. Lower Guard

5. Mitre locking knob

6. Mitre latch button

7. Kerf plate

8. Mitre scale

9. Mitre scale indicator

10. Carry grips

11. Fence

12. Bevel lock knob

13. Rails

13a.Velcro strap

14. Dust port

15. Battery pack

16. Work light switch

17. Lock off lever

18. Rail lock screw

19. Clamp mounting hole

20. Lock down pin

Assembly (Fig. A)

Your mitre saw is part assembled in the carton.

uOpen the box and lift the saw out by using the carry grips

(10) in the base of the saw (Fig. A).

u Place the saw on a smooth, at surface such as a work-

bench or strong table.

u Examine Assembly diagram on page 2 of this manual to

become familiar with the saw and its various parts. The

section on adjustments will refer to these terms and you

must know what and where the parts are.

u The mitre locking knob (5) is not assembled for shipping.

Remove the mitre locking knob (5) from the packaging

and screw onto the saw, see gure G and J for position.

u Your saw has a built-in dust port (14) that allows either

the supplied, but not assembled, dust bag (35) or shop

vacuum system to be connected (Fig. N).

Kerf plate (Fig. J)

The kerf plate (7) is mounted to the table by 6 screws. The

kerf plate (7) height is not adjustable.

Note: If the kerf plate (7) is worn, damaged or needs to be

replaced, repairs should be carried out by authorised repair

agents or Stanley Fat Max service staff.

Lock down pin (Fig. F)

Warning! The lock down pin should be used ONLY when

carrying or storing the saw. NEVER use the lock down pin for

any cutting operation.

Note: To lift, carry and support the mitre saw during transport

use the two carrying handles (10) located on both sides of the

mitre saw base (Fig. A).

To lock the saw head in the down position, push the saw head

down, push the lock down pin (20) in and release the saw

head. This will hold the saw head safely down for transporting

the saw from place to place. To release, press the saw head

down and pull the pin out.

Warning! Always be sure that the tool is switched off and the

battery is removed from the tool before adjusting or checking

the tools function.

Charging a battery (g. B)

Stanley FatMax chargers are designed to charge Stanley

FatMax battery packs.

u Plug the charger (21) into an appropriate outlet before

inserting a battery pack (15).

u Insert the battery pack (15) into the charger, making sure

the battery pack is fully seated in the battery slots

(Figure B).

The LED (21a) will ash indicating that the

battery is being charged.

The completion of charge is indicated by the

LED remaining on continuously. The pack is

fully charged and may be used at this time or

left in the charger.

u Recharge discharged batteries as soon as possible after

use or battery life may be greatly diminished.

u For longest battery life, do not discharge batteries fully.

It is recommended that the batteries be recharged after

each use.

Charger diagnostics (g. C)

This charger is designed to detect certain problems that can

arise with the battery packs or the power source. Problems

are indicated by one LED ashing in different patterns.

Bad battery

The charger can detect a weak or damaged

battery. The LED ashes in the pattern indi-

cated on the label. If you see this bad battery

blink pattern, do not continue to charge the battery. Return it

to a service centre or a collection site for recycling.

Hot/cold pack delay

When the charger detects a battery that

is excessively hot or excessively cold, it

automatically starts a Hot/Cold Pack Delay,

suspending charging until the battery has normalized. After

this happens, the charger automatically switches to the Pack

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley FMCS701 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info