Bedienungsanleitung Stanley FMCW210 (Seite 7 von 80) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

720720

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

ENGLISH

(Original instructions)

It is recommended that the batteries be recharged after each

use.

Leaving the battery in the charger

The charger (5) and battery pack (4) can be left connected

with the LED glowing indenitely.

The charger will keep the battery pack fresh and fully charged.

Important charging notes

u Longest life and best performance can be obtained if

the battery pack is charged when the air temperature is

between 65°F and 75°F (18°- 24°C). DO NOT charge the

battery pack in an air temperature below +40°F (+4.5°C),

or above +105°F (+40.5°C). This is important and will

prevent serious damage to the battery pack.

u The charger and battery pack may become warm to touch

while charging. This is a normal condition, and does not

indicate a problem. To facilitate the cooling of the battery

pack after use, avoid placing the charger or battery pack

in a warm environment such as in a metal shed, or an

uninsulated trailer.

u If the battery pack does not charge properly:

u Check current at receptacle by plugging in a lamp or

other appliance.

u Check to see if receptacle is connected to a light switch

which turns power off when you turn out the lights.

u Move charger and battery pack to a location where the

surrounding air temperature is approximately 65°F

- 75°F (18°- 24°C).

u If charging problems persist, take the tool, battery pack

and charger to your local service center.

u The battery pack should be recharged when it fails to

produce sufcient power on jobs which were easily done

previously. DO NOT CONTINUE to use under these

conditions. Follow the charging procedure. You may also

charge a partially used pack whenever you desire with no

adverse affect on the battery pack.

u Foreign materials of a conductive nature such as, but

not limited to, steel wool, aluminium foil, or any buildup

of metallic particles should be kept away from charger

cavities. Always unplug the charger from the power supply

when there is no battery pack in the cavity. Unplug charger

before attempting to clean.

u Do not freeze or immerse charger in water or any other

liquid.

Warning! Do not allow any liquid to get inside charger. Never

attempt to open the battery pack for any reason.

If the plastic housing of the battery pack breaks or cracks,

return to a service center for recycling.

Charger Diagnostics (Fig.B)

Refer to the indicators in gure B for the charge status of the

battery pack.

Bad Battery

If you see a bad battery blink pattern, do not continue

to charge this battery. Return it to a service center or a

collection site for recycling.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot

or too cold, it automatically starts a Hot/Cold Pack Delay,

suspending charging until the battery pack has reached an

appropriate temperature. The charger then automatically

switches to the pack charging mode. This feature ensures

maximum battery pack life. A cold battery pack will charge at a

slower rate than a warm battery pack. The pack will charge at

that slower rate throughout the entire charging cycle and will

not return to maximum charge rate even if the pack warms.

Installing and removing the battery pack from the

tool

To install battery pack (Fig. C)

u Insert battery (4) into tool foot until an audible click is

heard (Figure. C)

u Ensure battery pack is fully seated and fully latched into

position.

To remove battery pack (Fig.D)

u Depress the battery release button (4a) as shown in gure

D and pull battery pack (4) out of tool foot.

Assembly

Warning! Before assembly, make sure that the tool is

switched off and the battery is removed.

Fitting sanding mesh (Fig. E)

u Hold the tool with the sanding base facing upwards.

u Place the sanding mesh (6) onto the sanding base, mak-

ing sure that the holes in the sheet line up with the holes

in the base.

Fitting sanding sheets (Fig. F - Optional accessory)

u Detach the two additional diamond-shaped tips (8) from

the sanding sheet (7).

The diamond-shaped tip (8) can be reversed and replaced

when worn.

u When the front part of the tip (8) is worn, detach it from the

sheet, reverse it and press it onto the sanding base again.

u When the whole tip is worn, remove it from the sanding

base and t a new tip.

For optimal dust collection, ensure the correct type of sanding

paper is used.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley FMCW210 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info