Bedienungsanleitung Stanley FME301 (Seite 6 von 80) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

720711

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

ENGLISH

(Original instructions)

5. Spindle lock button

6. Shoe

7. Saw blade

8. Saw blade guard

9. Guard handle

10. Saw dust outlet

Assembly

Warning! Before attempting any of the following operations,

make sure that the tool is switched off and unplugged and that

the saw blade has stopped.

Removing and tting a saw blade (g. A)

Removing

u Keep the spindle lock button (5) depressed and rotate the

blade until the spindle lock engages.

u Loosen and remove the blade retaining screw (11) by turn-

ing it counterclockwise using the spanner (12) supplied.

u Remove the outer washer (13).

u Remove the saw blade (7).

Fitting

u Place the saw blade onto the inner ange (14), making

sure that the arrow on the blade points in the same direc-

tion as the arrow on the tool.

u Fit the outer washer (13) on the spindle, with the raised

part pointing away from the saw blade.

u Insert the blade retaining screw (11) into the hole.

u Keep the spindle lock button (5) depressed.

u Securely tighten the blade retaining screw by turning it

clockwise using the spanner (12) supplied.

Fitting and removing the parallel fence (g. B)

u The parallel fence is used to saw in a straight line parellel

to the edge of the workpiece.

Fitting

u Loosen the locking knob (16).

u Insert the parallel fence (17) through the openings (18).

u Slide the parallel fence into the desired position.

u Tighten the locking knob.

Removing

u Loosen the locking knob.

u Pull the parallel fence off the tool.

Use

Warning! Let the tool work at its own pace. Do not overload.

This tool can be used in the right hand or the left hand.

Adjusting the sawing angle (g. C)

u Use a square to check that the angle between the saw

blade and the shoe is 90

. If the angle does not measure

adjust as follows:

u Loosen the locking knob (19) to unlock the saw shoe.

u Loosen the locknut (20) on the adjusting screw (21).

u Screw the adjusting screw in or out to achieve a 90o

angle.

u Retighten the locknut.

u Tighten the locking knob to lock the saw shoe in place.

Adjusting the depth of cut (g. D)

The depth of cut should be set according to the thickness of

the workpiece. It should exceed the thickness by approx. 2

mm.

u Loosen the knob (20) to unlock the saw shoe.

u Move the saw shoe (6) into the desired position. The cor-

responding depth of cut can be read from the scale (21).

u Tighten the knob to lock the saw shoe in place.

Adjusting the bevel angle (g. E)

This tool can be set to bevel angles between 0

and 45

u Loosen the locking knob (19) to unlock the saw shoe.

u Move the saw shoe (6) into the desired position. The cor-

responding bevel angle can be read from the scale (24).

u Tighten the locking knob to lock the saw shoe in place.

Switching on and off

u To switch the tool on, move the lock-off button (2) into the

unlock position and squeeze the on/off switch (1).

u To switch the tool off, release the on/off switch.

Sawing

Always hold the tool with both hands.

u Let the blade run freely for a few seconds before starting

the cut.

u Apply only a gentle pressure to the tool while performing

the cut.

u Work with the shoe pressed against the workpiece.

Note: Take care not to allow the blade tips to overheat.

Using the sight guide (g. F)

The tool is equipped with a sight guide for straight cutting (25).

u Adjust the sight guide as described below.

u Align the left edge of the guides (25) with the cutting line

(26).

Dust extraction

An adaptor is required to connect a vacuum cleaner or dust

extractor to the tool.

u Insert the dust extraction adaptor into the saw dust outlet

(10).

u Connect the vacuum cleaner hose to the adaptor.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley FME301 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info