Bedienungsanleitung Stanley FME650 (Seite 8 von 96) (Alle Sprachen)

622605

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

ENGLISH

(Original instructions)

Use

Warning! Let the tool work at its own pace. Do not overload.

Warning! Before cutting into walls, oors or ceilings, check for

the location of wiring and pipes.

Variable speed control (g. H)

The variable speed control allows you to adapt the speed of

the tool to the application.

u Set the variable speed dial (2) to the desired setting. At

setting 1 the tool will operate at low speed, 10,000 min-1.

At setting 6 the tool will operate at the maximum speed,

22,000 min-1.

Switching on and off (g. I)

u To switch the tool on, slide the on/off switch (1) forward

(position I).

u To switch the tool off, slide the on/off switch (1) to the rear

(position O).

Cut guide (g. F & J)

This feature allows you to more accurately track a marked

cut line.

u To use the cut guide, insert the guide (13) as shown in

gure J into the front slot on the depth/cut guide block (8).

u Adjust the length of the guide by pulling out or pushing

inward to achieve the desired cut depth.

u Secure the guide in place by turning the depth/cut adjust-

ment knob (12) clockwise. To release the guide turn the

depth/cut adjustment knob anti-clockwise.

Depth guide (g. F & K)

This feature allows you to precisely cut material at a specied

depth.

u To use the depth guide, insert the guide (13) as shown in

gure K into the front slot on the depth/cut guide block (8).

u Adjust the length of the guide by pulling out or pushing

inward to achieve the desired cut depth.

u Secure the guide in place by turning the depth/cut adjust-

ment knob (12) clockwise. To release the guide turn the

depth/cut adjustment knob anti-clockwise.

Hints for optimum use

u Always hold the tool securely. For precision work, hold the

tool near the front.

u Clamp the workpiece whenever possible, especially when

using cutting blades.

u Do not exert too much pressure on the tool.

u Always use the appropriate type of attachment for the

workpiece material and type of cut.

u Regularly check the condition of accessories. Replace

when necessary.

u Mark the desired starting point.

u Switch the tool on and slowly feed attachments into the

workpiece at the desired starting point.

u Clamp a piece of plywood or soft wood to the back of the

workpiece and saw through the combination in order to

obtain a clear cut.

u Do not force the cutting blade into the workpiece. Note

that cutting sheet metal will normally take more time than

sawing thicker wooden workpieces.

u When cutting metal spread a thin lm of oil along the cut-

ting line before cutting.

u When sanding new layers of paint before applying another

layer, use extra ne grit.

u On very uneven surfaces, or when removing layers of

paint, start with a coarse grit. On other surfaces, start with

a medium grit. In both cases, gradually change to a ne

grit for a smooth nish.

u Consult your retailer for more information on available

accessories.

Maintenance

Your Stanley Fat Max corded/cordless appliance/tool has

been designed to operate over a long period of time with a

minimum of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

Warning! Before performing any maintenance on corded/

cordless power tools:

u Switch off and unplug the appliance/tool.

u Or switch off and remove the battery from the appliance/

tool if the appliance/tool has a separate battery pack.

u Or run the battery down completely if it is integral and then

switch off.

u Regularly clean the ventilation slots in your appliance/tool/

charger using a soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner.

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be tted:

u Safely dispose of the old plug.

u Connect the brown lead to the live terminal in the new

plug.

u Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal.

Follow the tting instructions supplied with good quality plugs.

Recommended fuse: 5 A.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley FME650 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info