Bedienungsanleitung Stanley FME822 (Seite 7 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

720757

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

ENGLISH

(Original instructions)

guard specic for the intended operation. If the unit is intended

to perform cutting off operations, a guard (17, Fig F) specic

for this operation must be tted .

Fitting

u Place the tool on a table, with the spindle (5) facing up.

u Release the clamping lock (7) and hold the guard (4) over

the tool as shown.

u Align the lugs (8) with the notches (9).

u Press the guard down and rotate it counterclockwise to

the required position.

u Fasten the clamping lock (7) to secure the guard to the

tool.

u If required, tighten the screw (6) to increase the clamping

force.

Removing

u Release the clamping lock (7).

u Rotate the guard clockwise to align the lugs (8) with the

notches (9).

u Remove the guard from the tool.

Warning! Never use the tool without the guard.

Fitting the side handle

u Screw the side handle (2) into one of the mounting holes

in the tool.

Warning! Always use the side handle.

Fitting and removing grinding or cutting discs

(g. B - D)

Always use the correct type of disc for your application.

Always use discs with the correct diameter and bore size (see

technical data).

Fitting

u Fit the guard as described above.

u Place the inner ange (10) onto the spindle (5) as shown

(g. B). Make sure that the ange is correctly located on

the at sides of the spindle.

u Place the disc (11) onto the spindle (5) as shown (g. B).

If the disc has a raised centre (12), make sure that the

raised centre faces the inner ange.

u Make sure that the disc locates correctly on the inner

ange.

u Place the outer ange (13) onto the spindle. When tting

a grinding disc, the raised centre on the outer ange must

face towards the disc (A in g. C). When tting a cutting

disc, the raised centre on the outer ange must face away

from the disc (B in g. C).

u Keep the spindle lock (3) depressed and tighten the outer

ange using the two-pin spanner (14) (g. D).

Removing

u Keep the spindle lock (3) depressed and loosen the outer

ange (13) using the two-pin spanner (14) (g. D).

u Remove the outer ange (13) and the disc (11).

Fitting and removing sanding discs (g. D & E)

For sanding, a backing pad is required. The backing pad is

available from your Stanley Fat Max dealer as an accessory.

Fitting

u Place the inner ange (10) onto the spindle (5) as shown

(g. E). Make sure that the ange is correctly located on

the at sides of the spindle.

u Place the backing pad (15) onto the spindle.

u Place the sanding disc (16) onto the backing pad.

u Place the outer ange (13) onto the spindle with the raised

centre facing away from the disc.

u Keep the spindle lock (3) depressed and tighten the outer

ange using the two-pin spanner (14) (g. D). Make sure

that the outer ange is tted correctly and that the disc is

clamped tightly.

Removing

u Keep the spindle lock (3) depressed and loosen the outer

ange (13) using the two-pin spanner (14) (g. D).

u Remove the outer ange (13), the sanding disc (16) and

the backing pad (15).

Use

Warning! Let the tool work at its own pace. Do not overload.

u Carefully guide the cable in order to avoid accidentally

cutting it.

u Be prepared for a stream of sparks when the grinding or

cutting disc touches the workpiece.

u Always position the tool in such a way that the guard

provides optimum protection from the grinding or cutting

disc.

Switching on and off

u To switch on, slide the on/off switch (1) forward then press

it in. Note that the tool will continue running when you

release the switch.

u To switch off, press the rear part of the on/off switch.

Warning! Do not switch the tool off while under load.

Soft Start Feature

The soft start feature allows a slow speed build-up to avoid

an initial jerk when starting. This feature is particularly useful

when working in conned spaces.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley FME822 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info