Bedienungsanleitung Stanley FMEG210 (Seite 8 von 136) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

720758

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

ENGLISH

(Original instructions)

Voltage drops

Inrush currents cause short-time voltage drops. Under

unfavourable power supply conditions, other equipment may

be affected.

If the system impedance of the power supply is lower than

0.107 Ω, disturbances are unlikely to occur

Features

This tool includes some or all of the following features.

1. On/off switch

2. Spindle lock

3. Guard

4. Side handle

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fitting and removing the guard (g. A)

The tool is supplied with a guard intended for grinding

purposes only (type 27). If the unit is intended to perform

cutting off operations, a guard specic for this operation (type

41) must be tted. A suitable guard part numbers N551980

(for 115mm cutting wheel) and N542445 (for 125mm cutting

wheel) are available and can be obtained from Stanley Fat

Max service centres. Fitting

u Place the tool on a table, with the spindle (4) facing up.

u Release the clamping lock (5) and hold the guard (3) over

the tool as shown.

u Align the lugs (6) with the notches (7).

u Press the guard down and rotate it counterclockwise to

the required position.

u Fasten the clamping lock (5) to secure the guard to the

tool.

u If required, tighten the screw (8) to increase the clamping

force.

Removing

u Release the clamping lock (5).

u Rotate the guard clockwise to align the lugs (6) with the

notches (7).

u Remove the guard from the tool.

Warning! Never use the tool without the guard.

Fitting the side handle

u Screw the side handle (4) into one of the mounting holes

in the tool.

Warning! Always use the side handle.

Fitting and removing grinding discs

(g. B - D)

Always use the correct type of disc for your application.

Always use discs with the correct diameter and bore size (see

technical data).

Fitting

u Fit the guard as described above.

u Place the inner ange (9) onto the spindle (4) as shown

(g. B). Make sure that the ange is correctly located on

the at sides of the spindle.

u Place the disc (10) onto the spindle (4) as shown (g. B).

If the disc has a raised centre (11), make sure that the

raised centre faces the inner ange.

u Make sure that the disc locates correctly on the inner

ange.

u Place the outer ange (12) onto the spindle. When tting

a grinding disc, the raised centre on the outer ange must

face towards the disc (A in g. C). When tting a cutting

disc, the raised centre on the outer ange must face away

from the disc (B in g. C).

u Keep the spindle lock (2) depressed and tighten the outer

ange using the two-pin spanner (13) (g. D).

Removing

u Keep the spindle lock (2) depressed and loosen the outer

ange (12) using the two-pin spanner (13) (g. D).

u Remove the outer ange (12) and the disc (10).

Surface grinding with grinding discs

u Allow the tool to reach full speed before touching the tool

to the work surface.

u Apply minimum pressure to the work surface, allowing the

tool to operate at high speed. Grinding rate is greatest

when the tool operates at high speed.

u Maintain a 20˚ to 30˚ angle between the tool and work

surface as shown in gure F.

u Continuously move the tool in a forward and back motion

to avoid creating gouges in the work surface.

u Remove the tool from work surface before turning tool off.

Allow the tool to stop rotating before laying it down.

Edge grinding with grinding discs

Wheels used for cutting and edge grinding may break or kick

back if they bend or twist while the tool is being used to do

cutoff work or deep grinding. Edge grinding/ cutting with a

Type 27 wheel must be limited to shallow cutting and notching,

less than 13 mm in depth when the wheel is new. Reduce the

depth of cutting/notching equal to the reduction of the wheel

radius as it wears down. Refer to the 'Grinding and cutting

accessory chart' at the end of ths manual for more

information. Edge grinding/cutting with a Type 41 wheel

requires usage of a Type 41 guard.

u Allow the tool to reach full speed before touching the tool

to the work surface.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley FMEG210 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info