Bedienungsanleitung Stanley FMHT0-77422 (Seite 6 von 194) (Alle Sprachen)

720798

Zoom out

Zoom in

Vorherige Seite

1/194

Nächste Seite

• Always insert batteries correctly with regard to polarity

(+ and –), as marked on the battery and the equipment.

• Do not short battery terminals.

• Do not charge disposable batteries.

• Remove dead batteries immediately and dispose of per

local codes.

• Do not dispose of batteries in re.

• Keep batteries out of reach of children.

• Remove batteries when the device is not in use.

Battery Installation (Figure B)

Open the battery cover (10) by gently pressing in at the

locations (23) shown in Figure B. Connect the 9V battery (24)

(6F22 or equivalent), ensuring polarity. Close battery door.

Battery Replacement (Figure B)

When the symbol

appears, the battery is low and

should be replaced.

Wait until the thermometer turns off automatically. Open the

battery cover (10) by gently pressing in at the locations (23)

shown in Figure B. Replace battery with 9V battery (24) (6F22

or equivalent), ensuring polarity is correct. Close battery door.

Components

THERMOMETER (Figure A)

1 Button

Button

4 MODE Button

5 Built-in 1/4-20 Nut

6 Handle

7 LCD Display

8 IR Sensor

9 Measurement Trigger

10 Battery Cover

11 Laser Pointer

NOTE: The thermometer can be attached to a suitable support

with a 1/4-20 bolt using the thermometer’s built in 1/4-20 nut (5).

LCD INSTRUCTION (Figure A)

12 MAIN DISPLAY shows the present reading or last reading.

13 DATA HOLD indicator appears when the reading on the

main display is locked.

14 MEASUREMENT INDICATOR appears and ashes when

the thermometer is taking measurements.

15 EMISSIVITY DISPLAY shows the present emissivity setting

value. TIP: The symbol

means Emissivity.

16 BACKLIGHT INDICATOR appears when the backlight

function is active.

17 TEMPERATURE UNIT applies to both the main display and

the bottom display.

18 SYMBOLS used to indicate the kind of value being

displayed on the bottom display. EXAMPLE: If the symbol

“ MAX “ appears, the value on the bottom display is the

maximum value.

19 BOTTOM DISPLAY used to display maximum (MAX),

minimum (MIN), difference (DIF), average (AVG), high alarm

value (HAL) and low alarm value (LAL).

is the high alarm icon, and is low

alarm icon.

21 LOW BATTERY INDICATOR

: Replace the battery

immediately when the low battery indicator appears.

22 LASER FUNCTION INDICATOR appears when the laser

function is enabled. When this indicator appears, the laser

pointer will emit a laser beam when the trigger is pulled.

BUTTON INSTRUCTIONS (Figure A)

1 Button

• Used to change temperature units from Celsius to

Fahrenheit value(s).

• When setting emissivity (

), high alarm value (HAL),

or low alarm value (LAL), press this button to

increase the value to be set

Button

• Press this button to turn on or off the backlight.

• To enable or disable the laser function, press

button while pulling and holding the trigger. When the

laser function is enabled, the symbol appears.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley FMHT0-77422 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info