Bedienungsanleitung Stanley FMHT1-77416 (Seite 10 von 212) (Alle Sprachen)

720743

Zoom out

Zoom in

Vorherige Seite

1/212

Nächste Seite

Push the battery compartment cover closed until it snaps in

place (Figure

#3).

Slide the Power/Transport Lock switch to the right to the

Unlocked/ON position (Figure

#1b).

On the keypad, make sure (Figure

#3) is not

ashing (> 5%). If is ashing, this means that the

battery level is below 5%.

• The laser may continue to operate for a short time while

the battery power continues to drain, but the laser lines

and dots will quickly dim.

• After fresh batteries are installed and the laser is turned

ON again, the laser lines and dots will return to full

brightness.

When the laser is not in use, slide the Power/Transport

Lock switch to the LEFT to the Locked/OFF position

(Figure

#1a) to save battery power.

Using the Mounting Block

On the bottom of the laser is a moveable block (Figure

• To use the magnets on the front of the laser (Figure

#2) to

mount the laser against the side of a steel beam, do not

extend the moveable block (Figure

#1). This will allow the

down dot to be aligned with the edge of the steel beam.

• To mount the laser over a point on the oor (using a multi-

function bracket or a tripod), pull out the moveable block until

it clicks in place (Figure

#2). This will allow the laser down

dot to display through the 5/8-11 mounting hole and the laser

to be rotated over the 5/8-11 mounting hole without moving

the vertical position of the laser.

Turning the Laser On

Place the laser on a smooth, flat, level surface, with the

laser facing straight ahead toward the opposing wall

(0º position).

Slide the Power/Transport Lock switch to the right to the

Unlocked/ON position (Figure

#1b).

Press (Figure

#6) once to display a horizontal laser

line, a second time to display a down dot, and a third time

to display a horizontal line and a down dot.

Check the laser beams. The laser is designed to self-level.

• If the laser is tilted so much that it cannot self-level

(> 4°), the laser beams will continually flash twice and

(Figure

#4) will flash constantly on the keypad.

• If the laser beams ash, the laser is not level (or plumb)

and should NOT BE USED for determining or marking

level or plumb. Try repositioning the laser on a level

surface.

Press (Figure

#5) once to display a vertical laser

line from the front of the laser, a second time to display

a vertical laser line from the side of the laser, and a third

time to display both vertical lines.

Press (Figure

#7) to test the Pulse mode. will

illuminate and the laser beams will appear lighter, since

they are ashing at a very rapid rate. You will only use

Pulse mode with a detector to display the laser beams long

range.

If ANY of the following statements are TRUE, continue with

the instructions for Checking Laser Accuracy BEFORE

USING THE LASER for a project.

• This is the first time you are using the laser (in case

the laser was exposed to extreme temperatures).

• The laser has not been checked for accuracy in

a while.

• The laser may have been dropped.

Checking Laser Accuracy

The laser tools are sealed and calibrated at the factory. It

is recommended that you perform an accuracy check prior

to using the laser for the rst time (in case the laser was

exposed to extreme temperatures) and then regularly to

ensure the accuracy of your work. When performing any of

the accuracy checks listed in this manual, follow these

guidelines:

• Use the largest area/distance possible, closest to the

operating distance. The greater the area/distance, the

easier to measure the accuracy of the laser.

• Place the laser on a smooth, at, stable surface that is

level in both directions.

• Mark the center of the laser beam.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley FMHT1-77416 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info