Bedienungsanleitung Stanley KFFMED1250 (Seite 6 von 52) (Deutsch, Englisch, Französisch, Portugiesisch, Spanisch, Polnisch, Türkisch)

720433

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

ENGLISH

(Original instructions)

Labels on tool

The following pictograms are shown on the tool along with the

date code:

Warning! To reduce the risk of injury, the user

must read the instruction manual.

Wear ear protectors with Impact drills. Exposure

to noise can cause hearing loss

Electrical safety

This tool is double insulated; therefore no earth

wire is required. Always check that the power

supply corresponds to the voltage on the rating

plate.

uIf the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Stanley FatMax Service

Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features.

1. On/Off switch

2. Speed selector dial

3. Drilling mode selector

4. Operating mode selector

5. Tool holder

6. Side handle

7. Depth stop

8. Grease cap

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fittingthesidehandle(g.A)

uTurn the grip counterclockwise until you can slide the side

handle (6) onto the front of the tool as shown.

uRotate the side handle into the desired position.

uTighten the side handle by turning the grip clockwise.

Fittingandsettingthedepthstop(g.A)

uSlacken the knob (9).

uInsert the depth stop (7) into the mounting hole as shown.

uSet the depth stop (7) to the desired position. The maxi-

mum drilling depth is equal to the distance between the tip

of the drill bit and the front end of the depth stop.

uTighten the knob (9).

Fittinganaccessory(g.B)

uClean and grease the shank (10) of the accessory.

uPull back the sleeve (11) and insert the shank into the tool

holder (5).

uPush the accessory down and turn it slightly until it ts into

the slots.

uPull on the accessory to check if it is properly locked. The

hammering function requires the accessory to be able to

move axially several centimetres when locked in the tool

holder.

uTo remove the accessory, pull back the sleeve (11) and

pull out the accessory.

Use

Warning! Let the tool work at its own pace. Do not overload.

Warning! Before drilling into walls, oors or ceilings, check for

the location of wiring and pipes.

Warning! Do not apply chisels when the tool is in the drilling

mode.

Selectingtheoperatingmode(g.D)

The tool can be used in three operating modes.

u To operate the drilling mode selector (3), rotate it towards

the required position, as indicated by the symbols.

u To operate the operating mode selector (4), push the

unlock button (16) and rotate the selector towards the

required position, as indicated by the symbols.

Drilling

u For drilling in steel, wood and plastics, and for screwdriv-

ing set the operating mode selector (4) to the

position

and the drilling mode selector (3) to the

position.

Hammer drilling

u For hammer drilling in masonry and concrete, set the

operating mode selector (4) to the

position and the

drilling mode selector (3) to the

position. When ham-

mering, the tool should not bounce and run smoothly. If

necessary, increase the speed.

Hammering

u For hammering with spindle lock, and for light chiselling

and chipping, set the operating mode selector (4) to the

position and the drilling mode selector (3) to the

position.

u When changing from hammer drilling to chiselling, turn

the chisel to the desired position. If resistance is felt

during mode change, slightly turn the chisel to engage the

spindle lock.

Switching on and off

u Select the required speed by turning the speed selector

dial (2).

u To switch the tool on, press the on/off switch (1).

u To switch the tool off, release the on/off switch.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley KFFMED1250 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info