Bedienungsanleitung Stanley KFFMED1250 (Seite 11 von 52) (Deutsch, Englisch, Französisch, Portugiesisch, Spanisch, Polnisch, Türkisch)

720433

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

(Übersetzung der ursprünglichen Anweisungen)

DEUTSCH

mum drilling depth is equal to the distance between the tip

of the drill bit and the front end of the depth stop.

uTighten the knob (9).

Fittinganaccessory(g.B)

uClean and grease the shank (10) of the accessory.

uPull back the sleeve (11) and insert the shank into the tool

holder (5).

uPush the accessory down and turn it slightly until it ts into

the slots.

uPull on the accessory to check if it is properly locked. The

hammering function requires the accessory to be able to

move axially several centimetres when locked in the tool

holder.

uTo remove the accessory, pull back the sleeve (11) and

pull out the accessory.

Use

Warning! Let the tool work at its own pace. Do not overload.

Warning! Before drilling into walls, oors or ceilings, check for

the location of wiring and pipes.

Warning! Do not apply chisels when the tool is in the drilling

mode.

Selectingtheoperatingmode(g.D)

The tool can be used in three operating modes.

u To operate the drilling mode selector (3), rotate it towards

the required position, as indicated by the symbols.

u To operate the operating mode selector (4), push the

unlock button (16) and rotate the selector towards the

required position, as indicated by the symbols.

Drilling

u For drilling in steel, wood and plastics, and for screwdriv-

ing set the operating mode selector (4) to the

position

and the drilling mode selector (3) to the

position.

Hammer drilling

u For hammer drilling in masonry and concrete, set the

operating mode selector (4) to the

position and the

drilling mode selector (3) to the

position. When ham-

mering, the tool should not bounce and run smoothly. If

necessary, increase the speed.

Hammering

u For hammering with spindle lock, and for light chiselling

and chipping, set the operating mode selector (4) to the

position and the drilling mode selector (3) to the

position.

u When changing from hammer drilling to chiselling, turn

the chisel to the desired position. If resistance is felt

during mode change, slightly turn the chisel to engage the

spindle lock.

Switching on and off

u Select the required speed by turning the speed selector

dial (2).

u To switch the tool on, press the on/off switch (1).

u To switch the tool off, release the on/off switch.

Brushmonitor(g.C)

Your tool has a built in system that monitors the health of the

brushes.

u Green brush monitor indicator (17). The brushes are in

good condition.

u Red brush monitor indicator (18). The brushes are warn

and need replacing, return your tool to an authorised

Stanley Europe Service Centre in order to to have the

brushes replaced.

Accessories

The performance of your tool depends on the accessory used.

Stanley Fat Max accessories are engineered to high quality

standards and designed to enhance the performance of your

tool. By using these accessories you will get the very best

from your tool.

Maintenance

Your Stanley Fat Max corded/cordless appliance/tool has

been designed to operate over a long period of time with a

minimum of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

uSwitch off and unplug the appliance/tool.

uRegularly clean the ventilation slots in your appliance/tool/

charger using a soft brush or dry cloth.

uRegularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner.

uRegularly open the chuck and tap it to remove any dust

from the interior (when tted).

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be tted:

uSafely dispose of the old plug.

uConnect the brown lead to the live terminal in the new

plug.

uConnect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal.

Follow the tting instructions supplied with good quality plugs.

Recommended fuse: 5 A.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley KFFMED1250 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info