Bedienungsanleitung Stanley KFFMED500 (Seite 5 von 96) (Alle Sprachen)

720421

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

ENGLISH

(Original instructions)

When assessing vibration exposure to determine safety

measures required by 2002/44/EC to protect persons regularly

using power tools in employment, an estimation of vibration

exposure should consider, the actual conditions of use and the

way the tool is used, including taking account of all parts of the

operating cycle such as the times when the tool is switched off

and when it is running idle in addition to the trigger time.

Labels on tool

The following pictograms are shown on the tool along with the

date code:

Warning! To reduce the risk of injury, the user

must read the instruction manual.

Wear ear protectors with Impact drills. Exposure

to noise can cause hearing loss

Electrical safety

This tool is double insulated; therefore no earth

wire is required. Always check that the power

supply corresponds to the voltage on the rating

plate.

If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Stanley

FatMax

Service

Centre in order to avoid a hazard .

Features

This tool includes some or all of the following features.

1. Variable speed switch

2. Lock-on button

3. Forward/reverse switch

4. Drilling mode selector

5. Tool holder

6. Side handle

7. Depth stop

8. Depth stop lock button

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fitting the side handle (ﬁ g. C

 Turn the grip counterclockwise until you can slide the side

handle (6) onto the front of the tool.

 Rotate the side handle into the desired position.

 Tighten the side handle by turning the grip clockwise.

Fitting an accessory (ﬁ g. A)

 Clean and grease the shank (9) of the accessory.

 Pull back the sleeve (10) and insert the shank into the tool

holder (5).

 Push the accessory down and turn it slightly until it ﬁ ts into

the slots.

 Pull on the accessory to check if it is properly locked. The

hammering function requires the accessory to be able to

move axially several centimetres when locked in the tool

holder.

 To remove the accessory, pull back the sleeve (10) and

pull out the accessory.

Use

Warning! Let the tool work at its own pace. Do not overload.

Warning! Before drilling into walls, ﬂ oors or ceilings, check for

the location of wiring and pipes.

Selecting the operating mode (ﬁ g. B)

The tool can be used in three operating modes. Press in the

button (11) and rotate the drilling mode selector (4) towards

the required position, as indicated by the symbols.

Drilling

 For drilling in steel, wood and plastics, set the operating

mode selector (4) to the

position.

Hammer drilling

 For hammer drilling in masonry and concrete, set the

operating mode selector (4) to the

position

 When hammering, the tool should not bounce and run

smoothly. If necessary, increase the speed.

Hammering

 For hammering with spindle lock, and for light chiselling

and chipping, set the operating mode selector (4) to the

position.

 Make sure the forward/reverse switch is in the forward

position.

 When changing from hammer drilling to chiselling, turn

the chisel to the desired position. If resistance is felt

during mode change, slightly turn the chisel to engage the

spindle lock.

 When hammering with spindle lock, the angle of the bit

may be changed. Set the operating mode selector (4) to

the

position, the angle of the bit may now be changed

by rotating the tool holder (6). Set the operating mode

selector (4) to the

position, before continuing.

Selecting the direction of rotation

For drilling, for tightening screws and for chiselling, use for-

ward (clockwise) rotation. For loosening screws or removing

a jammed drill bit, use reverse (counterclockwise) rotation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley KFFMED500 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info