Bedienungsanleitung Stanley RLD400 (Seite 6 von 104) (Alle Sprachen)

622246

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

77-132 / 77-133

To mount clamp onto measuring rod, pole, or similar object

(See ﬁ gure

) :

• Loosen tightening knob.

• Place onto measuring rod, pole, or similar object.

• Tighten knob to secure the clamp.

• When locating reference level loosen clamp to allow for

up / down positioning.

• When reference level is found, tighten knob again to

secure.

Operation

(See Keypad and LCD Descriptions for indications during

operation)

Power

• Press

to turn detector ON.

• When powered ON, the entire LCD will momentarily

display all icons (this allows a check to ensure that LCD

is functioning correctly).

• Press and hold

for ≥ 3 seconds to turn detector

OFF.

NOTE:

• The detector will automatically power OFF after 10 minutes

of not detecting a laser beam to conserve battery. To power

ON again, press

Illuminate LCD

• When detector is ON, press

to turn ON / OFF LCD

illumination.

NOTE:

The illumination will automatically turn OFF after 60 seconds of

not detecting a laser beam or having a key pressed.

Accuracy

• When powered ON, press

to toggle accuracy

setting between HIGH and LOW.

• When powered ON, the default accuracy setting is set

to HIGH.

NOTE:

• Only select LOW accuracy setting in times where HIGH

accuracy is not needed and / or when a stable reference

level cannot be obtained due to slight vibrations at or near

the work site.

• If the point to be measured is at a longer distance the LOW

accuracy setting may be necessary due to heat waves or

slight vibrations that may interfere with obtaining a stable

reference level.

Speaker Volume

• When powered ON,

press to toggle through the

volume settings (LOUD / SOFT / MUTE).

• When powered ON, the default volume setting is set

to LOUD.

Detecting Reference Level

• With detector ON, position within the general area

where the laser beam being referenced is being

projected towards.

• Use the bubble vial to maintain a level plane with the

detector.

• Be sure laser reception window is facing the direction of

the laser beam source.

• Move detector as indicated on the LCD to align datum

with laser beam.

• If speaker volume is ON (LOUD / SOFT), an audible tone

will sound to assist in communicating the positioning

of the detector.

• A beeping tone signals that the laser beam has been

detected. A fast beeping tone signals the detector

must be moved down. A slower beeping tone signals

the detector must be moved up. Again, the LCD also

indicates the direction the detector must be moved.

• A steady tone indicates that the laser beam is aligned

with the datum line on detector.

NOTE:

• When detecting the reference level the laser reception

window must face towards the laser source within a 40°

range from left to right.

Marking (See ﬁ gure

)

• Once the reference level has been detected, the position

can be marked at the datum line.

NOTE:

• Be sure to reference the back of the detector for the

measurement compensation value (distance from top to

datum) if the top of the detector was used as a marking

location.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley RLD400 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info