Bedienungsanleitung Stanley SDH600 (Seite 5 von 20) (Englisch, Französisch)

720417

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

(Original instructions) ENGLISH

Example:

2015 XX ZY

Year of manufacturing

Electrical safety

This tool is double insulated; therefore no earth

wire is required. Always check that the power

supply corresponds to the voltage on the rating

plate.

• If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised STANLEY Service Centre

in order to avoid a hazard.

Using an extension cable

• Always use an approved extension cable suitable for the

power input of this tool (see technical data). Before use,

inspect the extension cable for signs of damage, wear

and ageing. Replace the extension cable if damaged or

defective. When using a cable reel, always unwind the

cable completely. Use of an extension cable not suitable

for the power input of the tool or which is damaged or

defective may result in a risk of ﬁre and electric shock.

Features

This tool includes some or all of the following features.

1. Variable speed switch

2. Lock-on button

3. Forward/reverse button

4. Drilling mode selector

5. Chuck

6. Depth stop

7. Side handle

Assembly

Warning! Before assembly, make sure that the

tool is switched off and unplugged.

Fitting the side handle and depth stop

(ﬁg.A,B)

• Turn the grip counter clockwise until you can slide the

side handle (7) onto the front of the tool as shown (ﬁg.A).

• Rotate the side handle into the desired position.

• Insert the depth stop(6) into the mounting hole as shown

(ﬁg.B).

• Set the drilling depth as described below.

• Tighten the side handle by turning the grip clockwise.

Fitting a drill bit (ﬁg.C)

• Open the chuck by turning the sleeve (5) counter

clockwise.

• Insert the bit shaft (9) into the chuck (drill bit not

included).

• Insert the chuck key(10) into each hole (8) in the side of

the chuck and turn clockwise until it is tight.

Removing and reﬁtting the chuck (ﬁg.D)

• Open the chuck as far as possible.

• Remove the chuck retaining screw, located in the chuck,

by turning it clockwise using a screwdriver.

• Tighten an Allen key into the chuck and strike it with a

Impact as shown.

• Remove the Allen key. Remove the chuck by turning it

counter clockwise.

• To reﬁt the chuck, screw it onto the spindle and secure it

with the chuck retaining screw.

Use

Warning! Let the tool work at its own pace.Do not

overload.

Warning! Before drilling into walls, ﬂoors or

ceilings, check for the location of wiring and

pipes.

Selecting the direction of rotation (ﬁg.E)

For drilling and for tightening screws, use forward

(clockwise) rotation For loosening screws or removing a

jammed drill bit, use reverse (counter clockwise) rotation.

• To select forward rotation, push the forward/reverse

button (3) to the left position.

• To select reverse rotation, push the forward/reverse

button (3) to the right. Warning! Never change the

direction of rotation while the motor is running.

Selecting the drilling mode

• For drilling in masonry, set the drilling mode selector (4)

to the position.

• For drilling in other materials and for screwdriving, set

the drilling mode selector to the position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SDH600 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info