Bedienungsanleitung Stanley SDH700 (Seite 6 von 20) (Englisch, Französisch)

720418

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

ENGLISH (Original instructions)

Setting the drilling depth (ﬁg.B)

• Slacken the side handle (7) by turning the grip counter

clockwise.

• Set the depth stop(6) to the desired position. The

maximum drilling depth is equal to the distance between

the tip of the drill bit and the front end of the depth stop.

• Tighten the side handle by turning the grip clockwise.

Switching on and off

• To switch the tool on, press the variable speed switch(1).

The tool speed depends on how far you press the

switch. As a general rule, use low speeds for large

diameter drill bits and high speeds for smaller diameter

drill bits.

• For continuous operation, press the lock-on button (2)

and release the variable speed switch. This option is

available only at full speed in both forward and reverse

modes.

• To switch the tllo off, release the variable speed switch.

To switch the tool off when in continuous operation,

press the variable speed switch again and release it.

• Based on the different applications, turn around the

speed dial(11) to control the maximum speed.

Drilling in metal

Start drilling with slow speed and increase to full power while

applying ﬁrm pressure on the tool. A smooth even ﬂow of

metal chips indicates the proper drilling rate. Use a cutting

lubricant when drilling metals. The exceptions are cast iron

and brass which should be drilled dry.

NOTE: Large [5/16” (8 mm) to 1/2” (13 mm)] holes in steel

can be made easier if a pilot hole [5/32” (4 mm) to 3/16” (5

mm)] is drilled ﬁrst.

Drilling in wood

Start drilling with slow speed and increase to full power while

applying ﬁrm pressure on the tool. Holes in wood can be

made with the same twist drills used for metal. These bits

may overheat unless pulled out frequently to clear chips

from the ﬂutes. Work that is apt to splinter should be backed

up with a block of wood.

Drilling in masonry

When drilling in masonry, use carbide-tipped bits rated for

Impact drilling and be certain that the bits are sharp. Use a

constant and ﬁrm force on the tool to drill most effectively. A

smooth, even ﬂow of dust indicates the proper drilling rate.

Screwdriving

Select forward or reverse rotation.

Accessories

The performance of your tool depends on the accessory

used. STANLEY accessories are engineered to high quality

standards and designed to enhance the performance of your

tool. By using these accessories you will get the very best

from your tool.

Maintenance

Your tool has been designed to operate over a long period of

time with a minimum of maintenance. Continuous

satisfactory operation depends upon proper tool care and

regular cleaning.

Warning! Before performing any maintenance, switch off

and unplug the tool.

• Regularly clean the ventilation slots in your tool using a

soft brush or dry cloth.

• Regularly clean the motor housing using a damp cloth.

Do not use any abrasive or solvent-based cleaner.

Notes

• STANLEY’s policy is one of continuous improvement to

our products and as such, we reserve the right to change

product speciﬁcations without prior notice.

• Standard equipment and accessories may vary by

country.

• Product speciﬁcations may differ by country.

• Complete product range may not be available in all

countries. Contact your local STANLEY dealers for range

availability.

Service Information

STANLEY offers a full network of company-owned and/ or

authorized service agents throughout your country. All

STANLEY Service Centers are staffed with trained personnel

to provide customers with efﬁcient and reliable power tool

service. Whether you need technical advice, repair, or

genuine factory replacement parts, contact the STANLEY

location nearest to you.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SDH700 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info