Bedienungsanleitung Stanley SFMCBL7 (Seite 12 von 16) (Englisch)

720480

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

ENGLISH

Fuel Gauge Battery Packs (Fig. B)

Some STANLEYFATMAX battery packs include a fuel gauge

which consists of three green LED lights that indicate the level of

charge remaining in the batterypack.

To actuate the fuel gauge, press and hold the fuel gauge

button

9

. A combination of the three green LED lights will

illuminate designating the level of charge left. When the level of

charge in the battery is below the usable limit, the fuel gauge

will not illuminate and the battery will need to berecharged.

NOTE: The fuel gauge is only an indication of the charge left on

the battery pack. It does not indicate tool functionality and is

subject to variation based on product components, temperature

and end-userapplication.

Assembly (Fig. C)



CAUTION: Ensure the lock-off switch is in the locked

position to prevent the trigger switch from moving and

the battery is removed before attaching or removing the

tube assembly. The tube assembly must be attached to the

blower beforeuse.

TO ASSEMBLE BLOWER TUBES

1. Align the upper tube

4

to the blower and the lower tube

5

to the upper tube as shown in Fig. C.

2. Push the upper tube firmly onto the blower, until the lock

engages and an audible click is heard.

3. Then push the lower tube firmly into the upper tube, until

the lock engages and an audible click is heard.

4. Pull on the tubes to ensure they are securely in place.

NOTE: To remove either tube, insert a screwdriver into the

unlocking hole on the housing. Lift the tab inside and pull

tube out.

OPERATION

Instructions for Use



WARNING: Always observe the safety instructions and

applicableregulations.



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

Proper Hand Position (Fig. A, D)



WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position asshown.



WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

Hold the handle

3

with one hand. as shown in Figure D.

Switching On (Fig. A, E)



CAUTION: Do not point unit discharge at self

orbystanders.



CAUTION: Always wear safety glasses. Wear a filter mask

if the operation is dusty. Use of gloves, long pants and

substantial footwear is recommended. Keep long hair and

loose clothing away from openings and movingparts.

1. To turn the blower on, depress the variable speed trigger

1

2. Release the trigger to turn the blower off.

Boost Button

The boost button

is located on the tool handle. It allows

you to optimize the tools performance and boost the power as

needed.

• Switch the sweeper on.

• To activate the “boost” mode, press the

boost button

down.

• To deactivate the “boost” mode, press the

boost button

down.

• Operate in “Normal” mode for most sweeping needs. (Longer

runtime will be achieved.)

• Activate “boost” mode as needed to clear heavy or wetdebris.

MAINTENANCE

Your STANLEYFATMAX power tool has been designed

to operate over a long period of time with a minimum of

maintenance. Continuous satisfactory operation depends upon

proper tool care and regularcleaning.



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

The charger and battery pack are notserviceable.

Lubrication

Your power tool requires no additionallubrication.

Cleaning



WARNING: Blow dirt and dust out of the main housing

with dry air as often as dirt is seen collecting in and around

the air vents. Wear approved eye protection and approved

dust mask when performing thisprocedure.



WARNING: Never use solvents or other harsh chemicals

for cleaning the non-metallic parts of the tool. These

chemicals may weaken the materials used in these parts.

Use a cloth dampened only with water and mild soap.

Never let any liquid get inside the tool; never immerse any

part of the tool into aliquid.

Optional Accessories



WARNING: Since accessories, other than those offered by

STANLEYFATMAX, have not been tested with this product,

use of such accessories with this tool could be hazardous.

To reduce the risk of injury, only STANLEYFATMAX

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SFMCBL7 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info