Bedienungsanleitung Stanley SFMCN616 (Seite 10 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

720810

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

ENGLISH

(Original instructions)

Preparing the tool

Warning! NEVER spray or in any other way apply oil,

lubricants or cleaning solvents inside the tool. This can

seriously affect the life and performance of the tool.

Warning! The battery should always be removed and the

trigger lock-off engaged whenever any adjustments are made

or when tool is not in use.

u Read the Safety Instruction section of this manual.

u Wear eye and ear protection.

u Remove battery from tool and fully charge.

u Ensure magazine is empty of all fasteners.

u Check for smooth and proper operation of contact trip and

pusher assemblies. Do not use tool if either assembly is

not functioning properly.

u Keep tool pointed away from yourself and others.

u Insert fully charged battery pack.

Loading the Tool (Fig. F)

Warning! Keep the tool pointed away from yourself and

others. Serious personal injury may result.

Warning! Never load nails with the contact trip or

trigger activated.

Warning! Always remove battery pack before loading or

unloading nails.

Warning! The battery should always be removed and the

trigger lock-off engaged whenever any adjustments are made

or when tool is not in use.

Warning! Keep ngers clear of pusher to prevent injury.

u Insert fasteners into the bottom of the magazine (9).

u Pull pusher latch (10) downward until the nail follower (16)

falls behind the nails as shown in gure F.

u Release the pusher latch(10).

Unloading the Tool

Warning! The battery should always be removed and the

trigger lock-off engaged whenever any adjustments are made

or when tool is not in use.

u Press pusher latch release button (11).

u Manually slide nails towards the bottom of the

magazine (9).

u Open the jam clear door on the nosepiece to verify there

are no nails remaining.

Adjusting Depth (Fig. G)

The depth that the fastener is driven can be adjusted using

the depth adjustment wheel (3) on the side of the tool.

Warning!To reduce risk of serious injury from accidental

actuation when attempting to adjust depth, Always:

u Remove battery pack.

u Engage trigger lock-off.

u Avoid contact with trigger during adjustments.

Depth settings are on a sliding scale on the depth adjustment

indicator (4). The left side indicating the deepest and the right

side indicating the shallowest.

u To drive a nail deeper, rotate the depth adjustment

wheel (3) downwards. This will slide the depth adjustment

indicator (4) to the left on the scale.

u To drive a nail shallower, rotate the depth adjustment

wheel (3) upwards. This will slide the depth adjustment

indicator (4) to the right on the scale.

Work lights (Fig. H)

There are work lights (5) located on each side of the nailer.

Work lights turn on upon depressing the contact trip.

Note: These work lights are for illuminating the immediate

work surface and are not intended to be used as ashlights.

Low Battery Indicator

The work lights will ash and then turn off completely to

indicate low battery.

Jammed Nail Indicator

The work lights will ash continually if a nail becomes jammed

in the nose piece (see Clearing a jammed nail).

Stall Release (Fig. I)

Warning! If a stall occurs, the tool will disable itself and

will require you to reset it. To do so, follow instructions on

clearing a stalled condition. Next remove battery pack and

then reinsert battery pack. The tool will now be operational. If

the nailer is used in a rigorous application where all available

energy in the motor is used to drive a fastener, the tool may

stall. The driver blade did not complete the drive cycle and the

jam/stall indicator will ash. Rotate the stall release lever (6)

on the tool and the mechanism will release.

Note! The tool will disable itself and not reset until the battery

pack has been removed and reinserted. If the unit continues

to stall please review the material and fastener length to be

sure that it is not too rigorous an application. If the driver

blade does not automatically return to the home position

after rotating the stall release lever, proceed to “clearing a

jammed nail”.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SFMCN616 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info