Bedienungsanleitung Stanley SFMCPH845 (Seite 14 von 156) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

720496

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

ENGLISH

To Remove the Battery Pack from the Tool

1. Press the release button

10

and firmly pull the battery pack

out of the toolhandle.

2. Insert battery pack into the charger as described in the

charger section of thismanual.

Fuel Gauge Battery Packs (Fig.C)

Some STANLEYFATMAX battery packs include a fuel gauge

which consists of three green LED lights that indicate the level of

charge remaining in the batterypack.

To actuate the fuel gauge, press and hold the fuel gauge

button

11

. A combination of the three green LED lights will

illuminate designating the level of charge left. When the level of

charge in the battery is below the usable limit, the fuel gauge

will not illuminate and the battery will need to berecharged.

NOTE: The fuel gauge is only an indication of the charge left on

the battery pack. It does not indicate tool functionality and is

subject to variation based on product components, temperature

and end-userapplication.

Joining Trimmer Head Module to Handle

Module (Fig.A, D)

Combining the handle module



11



to the trimmer head

module



12



creates a pole trimmer that is approximately 6' (1.8

m).

1. Align the groove on the outside of the coupling end of the

handle module



11



with the tongue on the inside of the

coupling end of the trimmer head module



12



2. Slide the threaded sleeve



6



on the trimmer head module

down as far as possible and rotate the sleeve clockwise until

it stops and completely covers the orangethreads.



WARNING: Always check to make sure that the sleeve is

completely threaded on and that the threads are no longer

visible. Not threading the sleeve completely on could

result in the modules becoming disconnected creating a

hazardous condition. Periodically check the connections to

insure that no threads arevisible.

Detaching Trimmer Head Module (Fig.D)



WARNING: Sharp moving blade. To prevent accidental

operation, insure that battery is disconnected from the

handle before performing the following operations. Failure

to do this could result in serious personal injury.

When detaching the modules rest the handle module

11

on the ground and grasp the center of the trimmer head

module

12

with one hand. Use your other hand to loosen the

threaded sleeve and then pull the two halves apart.

OPERATION

Instructions for Use



WARNING: Always observe the safety instructions and

applicableregulations.



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

Proper Hand Position (Fig.D)



WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position asshown.



WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

Always hold the trimmer, as shown in the illustrations in this

manual, with one hand on the switch handle

14

and one hand

on the foam gripper

4

( .

Pivoting the Trimmer Head (Fig.A, E)

The trimmer head pivots 180° and can be locked into 5

different positions within that range. To avoid being pinched,

weargloves.

1. Press in on the locking latch

7

and raise the trimmerhead.

2. Lock the trimmer head into any of the 5 positions. Check

to make sure that trimmer head is locked into position by

trying to move the motor housing. If it is not locked, rotate it

to the closest lockposition.

Switch (Fig.A)

To turn the tool ON pull the lock button

1

back with your

thumb and then squeeze the trigger

2

. (Once the tool is

running you can release the lock button.) To turn the tool OFF,

release the trigger.

Trimming Instructions (Fig.A, F, G)



DANGER: KEEP HANDS AWAY FROMBLADES.



WARNING: To guard against injury, observe the

following:

• READ INSTRUCTION MANUAL BEFORE USING. SAVE

INSTRUCTIONMANUAL.

• Check the hedge for foreign objects such as wires or

fences before eachuse.

• KEEP HANDS ON HANDLES. DON’TOVERREACH.

• DO NOT USE UNDER WETCONDITIONS.



CAUTION: BLADE MAY COAST AFTER TURNOFF.

NOTE: Jamming the blade on large branches can

causedamage.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SFMCPH845 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info