Bedienungsanleitung Stanley SFMCPS620 (Seite 11 von 192) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

720559

Zoom out

Zoom in

Vorherige Seite

1/192

Nächste Seite

ENGLISH

• Do not use the pole saw to cut downtrees.

• Do not grasp the exposed saw chain when picking up or

holding the polesaw.

• Grip pole saw securely - one hand on the pole, the other on

thehandle.

• Keep finger off trigger until ready to makecut.

• Before starting pole saw, make sure chain is not

touchinganything.

• Keep all parts of body away from chain when pole saw

isrunning.

• Do not force pole saw while cutting. Apply light pressure.

It will do the job better and safer at the rate for which it

wasintended.

• Carry pole saw from one place to another:

- with battery removed,

- fingers off/away from trigger,

- by holding pole at balance point, and

- with guide bar and chain to rear and with

scabbardattached.

• Do not cut small brush and saplings with the pole saw. Slender

matter may catch in the chain and be whipped toward you.

This could also pull you offbalance.

• Do not operate in poorlighting.

• Keep firm footing and balance. Do not overreach.

Overreaching can result in loss of balance or exposure to

hotsurfaces.

• Keep all parts of your body away from any movingpart.

• Do not, under any circumstance, use any attachment or

accessory on this product, which was not provided with the

product, or identified as appropriate for use with this product

in this instructionmanual.

• Inspect pole saw before each use and after dropping or other

impacts. Ensure there are no significant defects ordamage.

Do Not Operate Pole Saw:

- while under the influence of alcohol, medication, ordrugs.

- in rain or in damp or wetareas.

- where highly flammable liquids or gases arepresent.

- if pole saw is damaged, adjusted incorrectly, or not fully

and securelyassembled.

- if trigger does not turn pole saw on and off. Chain must

stop moving when you release trigger. Have faulty switch

replaced by authorized service center. See Accessories

underMaintenance.

- while in ahurry.

- while in a tree or on aladder.

- while on aerial booms, buckets orplatforms.

- during high wind or stormingweather.

GENERAL SAFETY RULES



DANGER: Shock Hazard. Serious injury or death from

electrocution if power lines are contacted. Never use near

any electrical source, wires, or powerlines.



WARNING: For safe operation read and understand

owner’s manual. Wear face shield (and/or safety glasses)

and hard hat to protect against falling debris. Always have

a clear work area, retreat path, and be aware of limb/

branch location to avoid falling limbs and debris. Keep

bystanders 15 m away when operating saw. To reduce the

risk of electric shock do not use on wet surfaces. Do not

expose to rain. Storeindoors.

• To protect yourself from falling branches do not stand directly

under the branch or limb being cut. This unit should not be held at

an angle over

60°

from groundlevel.

• Keep the handles dry, clean, and free ofoil.

• Before you start the unit, make sure the chain is not contacting

anyobject.

• Make sure the cutting chain has stopped before setting the

unitdown.

Service

• Tool service must be performed only by qualified repair

personnel. Service or maintenance performed by unqualified

personnel could result in a risk of injury. Refer to the

Maintenance section of thismanual.

• When servicing a tool, use only identical replacement

parts. Follow instructions in the Maintenance section of

this manual. Use of unauthorized parts or failure to follow

maintenance instructions may create a risk of electric shock

orinjury.

Guard Against Kickback



WARNING: KICKBACK may occur when the nose or tip of

the guide bar touches an object, or when the wood closes

in and pinches the saw chain in the cut. Tip contact in

some cases may cause a lightning fast reverse reaction,

kicking the guide bar up and back towards the operator.

Pinching the saw chain along the top of the guide bar

may push the guide bar rapidly back towards the operator.

Either of these reactions may cause you to lose control of

the saw which could result in serious injury touser.



THE FOLLOWING PRECAUTIONS SHOULD BE

FOLLOWED TO MINIMIZE KICKBACK:

• Grip pole saw firmly. Hold the saw firmly with both hands

when the unit is running. Use a firm grip with thumbs and

fingers encircling the saw handle andpole.

• Do notoverreach.

• Keep proper footing and balance at alltimes.

• Don’t let the nose of the guide bar contact a log, branch,

ground or otherobstruction.

• Do not extend pole saw handle above shoulderheight.

• Use devices such as reduced kickback chain, chain braking

system and special guide bars that reduce the risks associated

withkickback.

• Only use replacement bars and chains specified by the

manufacturer or theequivalent.

• Never let the moving chain contact any object at the tip of the

guidebar.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SFMCPS620 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info