Bedienungsanleitung Stanley SFMCPS620 (Seite 17 von 192) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

720559

Zoom out

Zoom in

Vorherige Seite

1/192

Nächste Seite

ENGLISH

5. Once saw chain tension is correct, tighten hex head

screws

12

to clampbar.

6. When the saw chain is new check the tension frequently

(after disconnecting battery) during the first 2 hours of use

as a new chain stretchesslightly.

NOTE: Saw chain tension should be adjustedregularly.

Chain Oiling (Fig.H)

1. A high quality bar and chain oil or SAE30 weight motor

oil should be used for saw chain

14

and guide bar

13

lubrication. The use of a vegetable based bar and chain

oil is recommended when pruning trees. Mineral oil is not

recommended because it may harm trees. Never use waste

oil or very thick oil. These may damage your polesaw.

2. Lubricate the whole saw chain evenly before each use as

shown in FigureH. Also lubricate the saw chain whenever

replacing a fully discharged battery with a fully chargedone.

Transporting Pole Saw (Fig. A)

Always remove the battery pack

6

from the handle and cover

the saw chain

14

with the scabbard

15

when transporting the

pole saw.

Joining Saw Head Module to HandleModule

(Fig. I–L)



WARNING: Sharp moving blade. To prevent accidental

operation, insure that battery is disconnected from the

handle and that the protective scabbard is in place on the

chain before performing the following operations. Failure

to do this could result in serious personal injury.

The three assembliess which make up the pole saw are keyed

to insure correct assembly. If an assembly does not smoothly

attach to another do not force fit.

Combining the handle assembly

1

to the saw head

assembly

3

creates a pole saw that is approximately 1.8m in

length as shown in Fig. I.

To attach the handle assembly to the saw head assembly:

1. Align the groove

21

on the outside of the coupling end of

the handle assembly

1

with the tongue

22

on the inside

of the coupling end of the saw head assembly

3

. Refer to

Fig.J. Push the two sections completelytogether. Refer to

Fig.K.

2. Slide the threaded sleeve

9

on the saw head assembly

down as far as possible and rotate the sleeve clockwise

until it stops and completely covers the threads as shown

in Fig.L.



WARNING: Always check to make sure that the sleeve

is completely threaded on and that the red threads are

no longer visible. Not threading the sleeve completely

on could result in the assemblys becoming disconnected

creating a hazardous condition. Periodically check the

connections to insure that no red threads arevisible.

NOTE: The fuel gauge is only an indication of the charge left on

the battery pack. It does not indicate tool functionality and is

subject to variation based on product components, temperature

and end-userapplication.

Installing and Removing Saw Chain

(Fig. A, C–E)



WARNING: Sharp moving blade. To prevent accidental

operation, insure that battery is disconnected from the

handle before performing the following operations. Failure

to do this could result in serious personal injury.



CAUTION: Sharp moving blade. Always wear protective

gloves when installing or removing the chain. The chain is

sharp and can cut you when it is notrunning.

1. Place the pole saw on a firm surface. Rotate the two

hex head screws

12

counterclockwise with the hex

wrench 

16

provided.

2. Remove sprocket cover

11

, bar clamp

10

, and hex

headscrews.

3. To remove the saw chain

14

, rotate the screw

19

in the

front of the housing using the flat screwdriver end of the

wrench. Turning the screw counterclockwise allows the

guide bar

13

to recede and reduces the tension on the

chain so that it may beremoved.

4. Lift the worn saw chain out of the groove in the guidebar.

5. Flip guide barover.

6. To replace the saw chain, check to make sure that the slot in

the guide bar is over the location pins

20

shown in Fig.E and

that hole below the slot is located over the adjustmentpin.

7. Place new chain in groove of guide bar and around

sprocket. Make sure saw teeth are facing correct direction by

matching the graphic onhousing or guidebar.

8. Rotate the screw in the front of the housing clockwise to

increase the chaintension.

9. Replace sprocket cover, bar clamp, and hex headscrews.

10. Follow the instructions in the section Adjusting

ChainTension.

Adjusting Chain Tension (Fig. A,C,D,F,G)

1. With the pole saw still on a firm surface check the saw

chain

14

tension. The tension is correct when the saw chain

snaps back after being pulled 3 mm away from the guide

bar

13

with light force from the middle finger and thumb

as shown in Fig.F. There should be no “sag” between the

guide bar and the saw chain on the underside as shown in

Fig.G.

2. To adjust saw chain tension, loosen hex head

screws

12

3. Rotate the screw

19

in the front of the housing using the

flat screwdriver end of thewrench.

4. Do not over-tension the saw chain as this will lead to

excessive wear and will reduce the life of the guide bar and

saw chain. Overtensioning also reduces the amount of cuts

you will get per batterycharge.

Stanley SFMCPS620 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info