Bedienungsanleitung Stanley SFMCS701 (Seite 9 von 184) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

720684

Zoom out

Zoom in

Vorherige Seite

1/184

Nächste Seite

ENGLISH

(Original instructions)

h. Do not let familiarity gained from frequent use of tools

allow you to become complacent and ignore tool

safety principles. A careless action can cause severe

injury within a fraction of a second.

4. Power tool use and care

a. Do not force the power tool. Use the correct power

tool for your application. The correct power tool will do

the job better and safer at the rate for which it was

designed.

b. Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with

the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d. Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

e. Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage of

parts and any other condition that may affect the

power tools operation. If damaged, have the power

tool repaired before use. Many accidents are caused by

poorly maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

h. Keep handles and grasping surfaces dry, clean and

free from oil and grease. Slippery handles and greasy

surfaces do not allow for safe handling and control of the

tool in unexpected situations.

5. Battery tool use and care

a. Recharge only with the charger specied by the

manufacturer. A charger that is suitable for one type of

battery pack may create a risk of re when used with

another battery pack.

b. Use power tools only with specically designated

battery packs. Use of any other battery packs may create

a risk of injury and re.

c. When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys,

nails, screws, or other small metal objects, that can

make a connection from one terminal to another.

Shorting the battery terminals together may cause burns

or a re.

d. Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally

occurs, ush with water. If liquid contacts eyes,

additionally seek medical help. Liquid ejected from the

battery may cause irritation or burns.

e. Do not use a battery pack or tool that is damaged or

modied. Damaged or modied batteries may exhibit

unpredictable behaviour resulting in re, explosion or risk

of injury.

f. Do not expose a battery pack or tool to re or

excessive temperature. Exposure to re or temperature

above 130 ºC may cause explosion.

g. Follow all charging instructions and do not charge the

battery pack or tool outside the temperature range

specied in the instructions. Charging improperly or at

temperatures outside the specied range may damage the

battery and increase the risk of re.

6. Service

a. Have your power tool serviced by a qualied repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

b. Never service damaged battery packs. Service of

battery packs should only be performed by the

manufacturer or authorised service providers.

Safety instructions for mitre saws

u Mitre saws are intended to cut wood or wood-like

products, they cannot be used with abrasive cut-off

wheels for cutting ferrous material such as bars, rods,

studs, etc. Abrasive dust causes moving parts such as

the lower guard to jam. Spartks from abrasive cutting will

burn the lower guard, the kerf insert and other plastic

parts.

u Use clamps to support the workpiece whenever

possible. If supporting the workpiece by hand, you

must always keep your hand at least 100 mm from

either side of the saw blade. Do not use this saw to

cut pieces that are too small to be securely clamped

or held by hand. If your hand is placed too close to the

saw blade, there is an increased risk of injury from blade

contact.

u The workpiece must be stationary and clamped or

held against both the fence and the table. Do not feed

the workpiece into the blade or cut “freehand” in any

way. Unrestrained or moving workpieces could be thrown

at high speeds, causing injury.

u Push the saw through the workpiece. Do not pull the

saw through the workpiece.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SFMCS701 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info