Bedienungsanleitung Stanley SFMCW221 Fatmax V20 (Seite 9 von 12) (Englisch)

805836

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

ENGLISH

(Original instructions)

Use

Warning! Let the tool work at its own pace. Do not overload.

Switching on and off

u To switch the tool on, depress the on/off switch (1) at the

"I" position.

u To switch the tool off, depress the on/off switch (1) at

the"O" position.

Variable-Speed Dial

To operate the tool, select the speed setting you wish with the

speed dial (8) , and press the ON/OFF switch.

The speed setting can be adjusted either with the tool ON or

OFF.

Warning! Because the tool has a separate speed dial for

setting the speed, the tool will start at the speed where the

variable speed dial is set. Always ensure switch is off in the

"O" position before installing the battery pack.

Warning! Be sure to select the proper speed for your

sanding operation. If in doubt about the proper speed for your

operation, test the performance at low speed settings and

gradually increase until a comfortable speed is found.

Operation (Fig.H)

Grasp the sander as shown in gure H and turn it ON. Move it

in long, sweeping strokes along the surface, letting it do

the work.

Pushing down on the tool while sanding actually slows the

removal rate and produces an inferior quality nish.

Check your work often. Sander is capable of removing

material rapidly especially with coarse paper.

Precautions to take when sanding paint

Sanding of lead based paint is NOT RECOMMENDED due to

the difculty of controlling the contaminated dust. The greatest

danger of lead poisoning is to children and pregnant women.

Since it is difcult to identify whether or not a paint contains

lead without a chemical analysis, we recommend the following

precautions when sanding any paint:

Personal safety

u No children or pregnant women should enter the work

area where the paint sanding is being done until all clean

up is completed.

u A dust mask or respirator should be worn by all persons

entering the work area. The lter should be replaced daily

or whenever the wearer has difculty breathing. See your

local hardware store for the proper EN14683-approved

dust mask.

u NO EATING, DRINKING or SMOKING should be done

in the work area to prevent ingesting contaminated paint

particles.

Workers should wash and clean up BEFORE eating,

drinking or smoking. Articles of food, drink, or smoking

should not be left in the work area where dust would settle

on them.

Environmental safety

u Paint should be removed in such a manner as to minimize

the amount of dust generated.

u Areas where paint removal is occurring should be sealed

with plastic sheeting of 4 mils thickness.

u Sanding should be done in a manner to reduce tracking of

paint dust outside the work area.

Cleaning and disposal

u All surfaces in the work area should be vacuumed and

thoroughly cleaned daily for the duration of the sanding

project. Vacuum lter bags should be changed frequently.

u Plastic drop cloths should be gathered up and disposed

of along with any dust chips or other removal debris.

They should be placed in sealed refuse receptacles and

disposed of through regular trash pick-up procedures.

During clean up, children and pregnant women should be

kept away from the immediate work area.

u All toys, washable furniture and utensils used by children

should be washed thoroughly before being used again.

Dust Collection (Fig.I, J)

Warning! Collected sanding dust from sanding surface

coatings (polyurethane, linseed oil, etc.) can self=ignite and

cause re. To reduce risk, strictly follow sander manual and

coating manufacturer’s instructions.

u The dust bag should be emptied after every 10 minutes of

sanding.

u To attach the dust bag to the sander, line up the grooves

(14) on the side dust bag collar (15) with the dust bag

locks (16) on the dust port (17) .

u Slide the dust bag onto the dust port and turn the dust bag

clockwise to lock it in place as shown in Figure I.

u To remove, turn the dust bag counterclockwise and slide

the dust bag off.

u To empty the dust bag, remove it from the dust port

and dump the sanding debris into an appropriate trash

receptacle as shown in Figure J.

Connecting a vacuum cleaner)

u Insert the hose of the vacuum cleaner into the dust port

(17).

Accessories

Warning! Since accessories, other than those offered by

STANLEY FATMAX, have not been tested with this product,

use of such accessories with this tool could be hazardous.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SFMCW221 Fatmax V20 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info