Bedienungsanleitung Stanley SFMEE500 (Seite 7 von 84) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

720728

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

ENGLISH

(Original instructions)

c. Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d. Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained

users.

e. Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage of

parts and any other condition that may affect the

power tools operation. If damaged, have the power

tool repaired before use. Many accidents are caused by

poorly maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into

account the working conditions and the work to be

performed.

Use of the power tool for operations different from those

intended could result in a hazardous situation.

h. Keep handles and grasping surfaces dry, clean and

free from oil and grease. Slippery handles and grasping

surfaces do not allow for safe handling and control of the

tool in unexpected situations.

6. Service

a. Have your power tool serviced by a qualied repair

person using only identical replacement parts.

This will ensure that the safety of the power tool is

maintained.

Additional power tool safety warnings

Warning! Additional safety warnings for wall

sanders.

u This power tool is intended to function as a sander.

Read all safety warnings, instructions,illustrations

and specications provided with this power tool.

Failure to follow all instructions listed below may result

in electric shock, re and/or serious injury.

u Operations such as grinding, wire brushing,

polishing or cutting-off are not recommended to

be performed with this power tool. Operations for

which the power tool was not designed may create a

hazard and cause personal injury.

u Do not use accessories which are not specically

designed and recommended by the tool

manufacturer.

Just because the accessory can be attached to your

power tool, it does not assure safe operation.

u The rated speed of the accessory must be at least

equal to the maximum speed marked on the power

tool. Accessories running faster than their rated speed

can break and y apart.

u The outside diameter and the thickness of your

accessory must be within the capacity rating

of your power tool. Incorrectly sized accessories

cannot be adequately guarded or controlled.

u Threaded mounting of accessories must match the

grinder spindle thread. For accessories mounted

by anges, the arbour hole of the accessory must

t the locating diameter of the ange. Accessories

that do not match the mounting hardware of the power

tool will run out of balance, vibrate excessively and

may cause loss of control.

u Do not use a damaged accessory.

Before each use inspect the accessory such as

abrasive wheels for chips and cracks, backing pad

for cracks, tear or excess wear, wire brush for loose

or cracked wires. If the power tool or accessory is

dropped, inspect for damage or install an undamaged

accessory. After inspecting and installing an

accessory, position yourself and bystanders away

from the plane of the rotating accessory and run

the power tool at maximum no load speed for one

minute. Damaged accessories will normally break

apart during this test time.

u Wear personal protective equipment .Depending

on application, use face shield, safety goggles

or safety glasses. As appropriate, wear dust

mask, hearing protectors, gloves and shop

apron capable of stopping small abrasive or

workpiece fragments. The eye protection must

be capable of stopping ying debris generated by

various operations. The dust mask or respirator must

be capable of ltrating particles generated by your

operation. Prolonged exposure to high intensity noise

may cause hearing loss.

u Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment. Fragments of the

workpiece or of a broken accessory may y away and

cause injury beyond the immediate area of operation.

u Hold the power tool by insulated gripping surfaces

only, when performing an operation where the

cutting accessory may contact hidden wiring or

its own cord. Cutting accessory contacting a “live”

wire may make exposed metal parts of the power tool

“live” and could give the operator an electric shock.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SFMEE500 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info