Bedienungsanleitung Stanley SGS1045 (Seite 8 von 28) (Englisch, Französisch)

720763

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

ENGLISH (Original instructions)

• Make sure that the abrasive or grinding wheels are

rotating in the direction of the arrows on the accessories

and tool.

OPERATION

WARNING! Always observe the safety instructions and

applicable regulations.

WARNING! To minimize the danger of serious personal injury,

please switch off the tool power and disconnect all plugs

before adjusting or removing/installing any accessory. Before

reassembling the tool, press and release the trigger switch to

make sure the tool is already switched off.

WARNING!

• Make sure all materials to be grinded are secured in

position.

• Apply slight pressure to the tool. Do not apply side

pressure to the abrasive disc.

• Avoid overloading. If the tool becomes hot, let it spin for a

few minutes with no load.

• Be sure to hold the tool tightly with both hands (one hand

on housing, the other on side handle). Start the tool and

bring the grinding wheel on the workpiece.

• Keep the edge of the wheel tilted at angle from 15 to 30

degrees against the surface of the workpiece.

• When using a new grinding wheel, do not operate the

wheel in the B direction, otherwise, it will cut into the

workpiece. When the edge of wheel has been rounded off,

you are free to operate the grinder in either the A or B

direction.

Starting and Stopping (Fig. A)

WARNING! Before using the tool, check whether the handle is

tightened securely. Check whether the ON/OFF switch is

working normally.

Before plugging in the tool to the power supply, check whether

the switch is in the OFF (o) position when pressing the rear

end of the switch.

To start the tool, press the rear end of the switch and slide it

forward. Then press the front end of the switch to lock it.

Press the rear end of the switch to stop the tool.

WARNING! Do not switch the tool on or off while under load

conditions.

Proper Hand Position (Fig. F)

WARNING! To reduce the risk of serious personal injury,

ALWAYS use proper hand position as shown.

WARNING! To reduce the risk of serious personal injury,

ALWAYS hold securely in anticipation of a sudden reaction.

Proper hand position requires one hand on the side handle

(Figure A), with the other hand on the body of the tool, as

shown in Figure F.

Switches

Caution! Hold the body of the tool ﬁrmly to maintain control of

the tool at start up and during use and until the wheel or

accessory stops rotating. Make sure the wheel has come to a

complete stop be fore laying the tool down.

Note: To reduce unexpected tool movement, do not switch the

tool on or off while under load conditions. Allow the grinder to

run up to full speed before touching the work surface. Lift the

tool from the surface before turning the tool off. Allow the tool

to stop rotating before putting it down.

Slider switch (Fig. A)

WARNING! Before connecting the tool to a power supply, be

sure the slider switch is in the off position by pressing the rear

part of the switch and releasing. Ensure the slider switch is in

the off position as described above after any interruption in

power supply to the tool, such as the activation of a ground

fault interrupter, throwing of a circuit breaker, accidental

unplugging, or power failure. If the slider switch is locked on

when the power is connected, the tool will start unexpectedly.

To start the tool, slide the slider switch (1) toward the front of

the tool. To stop the tool, release the slider switch. For

continuous operation, slide the switch toward the front of the

tool and press the forward part of the switch inward. To stop

the tool while operating in continuous mode, press the rear

part of the slider switch and release.

Spindle lock (Fig. A)

The spindle lock (2) prevents the output shaft from rotating

when attaching or removing the grinding wheel. Only use the

spindle lock when the tool is switched off, power is unplugged,

and wheel stops completely.

Note: To minimize tool damages, don’t use the spindle lock

when the tool is operating.

Otherwise, it may damage the tool. The attached accessories

may come off and cause injury.

If using the spindle lock, press the spindle lock button and

rotate the output shaft until it stops.

Application on Metals

When applying the tool on metals, make sure that a

residual-current device (RCD) is inserted to prevent danger

from metal chips.

If the RCD causes power disconnection, have the tool sent to

an authorized Stanley dealer for repair.

WARNING! Under extreme working conditions, conductive

dust and grit may accumulate on the housing interior when

handling metal workpieces.

This could create an electric shock hazard as it weakens the

protective insulation in the grinder.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SGS1045 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info