Bedienungsanleitung Stanley SGV115 (Seite 5 von 28) (Englisch, Französisch)

720764

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

(Original instructions) ENGLISH

SAFETY INSTRUCTIONS FOR ALL OPERATIONS

Safety warnings common for grinding.

• This power tool is intended to function as a grinder.

Read all safety warnings, instructions, illustrations

and speciﬁcations provided with this power tool.

Failure to follow all instructions listed below may result in

electric shock, ﬁre and/or serious injury.

• Operations such as polishing are not recommended to

be performed with this power tool. Operations for which

the power tool was not designed may create a hazard and

cause personal injury.

• Do not use accessories which are not speciﬁcally

designed and recommended by the tool manufacturer.

Just because the accessory can be attached to your

power tool, it does not assure safe operation.

• The rated speed of the accessory must be at least

equal to the maximum speed marked on the power

tool. Accessories running faster than their rated speed

can break and ﬂy apart.

• The outside diameter and the thickness of your

accessory must be within the capacity rating of your

power tool. Incorrectly sized accessories cannot be

adequately guarded or controlled.

• Threaded mounting of accessories must match the

grinder spindle thread. For accessories mounted by

ﬂanges, the arbour hole of the accessory must ﬁt the

locating diameter of the ﬂange. Accessories that do not

match the mounting hardware of the power tool will run out

of balance, vibrate excessively and may cause loss of

control.

• Do not use a damaged accessory. Before each use

inspect the accessory such as abrasive wheel for

chips and cracks, backing pad for cracks, tear or

excess wear, wire brush for loose or cracked wires. If

power tool or accessory is dropped, inspect for

damage or install an undamaged accessory. After

inspecting and installing an accessory, position

yourself and bystanders away from the plane of the

rotating accessory and run the power tool at

maximum no-load speed for one minute. Damaged

accessories will normally break apart during this test time.

• Wear personal protective equipment. Depending on

application, use face shield, safety goggles or safety

glasses. As appropriate, wear dust mask, hearing

protectors, gloves and work shop apron capable of

stopping small abrasive or workpiece fragments. The

eye protection must be capable of stopping ﬂying

debris generated by various operations. The dust mask

or respirator must be capable of ﬁltrating particles

generated by your operation. Prolonged exposure to high

intensity noise may cause hearing loss.

• Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment. Fragments of workpiece

or of a broken accessory may ﬂy away and cause injury

beyond immediate area of operation.

• Hold power tool by insulated gripping surfaces only,

when performing an operation where the cutting

accessory may contact hidden wiring or its own cord.

Cutting accessory contacting a “live” wire may make

exposed metal parts of the power tool “live” and shock the

operator.

• Position the cord clear of the spinning accessory. If

you lose control, the cord may be cut or snagged and your

hand or arm may be pulled into the spinning accessory.

• Never lay the power tool down until the accessory has

come to a complete stop. The spinning accessory may

grab the surface and pull the power tool out of your

control.

• Do not run the power tool while carrying it at your

side. Accidental contact with the spinning accessory could

snag your clothing, pulling the accessory into your body.

• Regularly clean the power tool’s air vents. The motor’s

fan will draw the dust inside the housing and excessive

accumulation of powdered metal may cause electrical

hazards.

• Do not operate the power tool near ﬂammable

materials. Sparks could ignite these materials.

• Do not use accessories that require liquid coolants.

Using water or other liquid coolants may result in

electrocution or shock.

FURTHER SAFETY INSTRUCTIONS FOR ALL

OPERATIONS

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or snagged rotating

wheel, backing pad, brush or any other accessory. Pinching or

snagging causes rapid stalling of the rotating accessory which

in turn causes the uncontrolled power tool to be forced in the

direction opposite of the accessory’s rotation at the point of the

binding.

For example, if an abrasive wheel is snagged or pinched by the

workpiece, the edge of the wheel that is entering into the pinch

point can dig into the surface of the material causing the wheel

to climb out or kick out. The wheel may either jump toward or

away from the operator, depending on direction of the wheel’s

movement at the point of pinching. Abrasive wheels may also

break under these conditions. Kickback is the result of tool

misuse and/or incorrect operating procedures or conditions and

can be avoided by taking proper precautions as given below:

• Maintain a ﬁrm grip on the power tool and position

your body and arm to allow you to resist kickback

forces. Always use auxiliary handle, if provided, for

maximum control over kickback or torque reaction

during start up. The operator can control torque reaction

or kickback forces, if proper precautions are taken.

• Never place your hand near the rotating accessory.

Accessory may kickback over your hand.

• Do not position your body in the area where power

tool will move if kickback occurs. Kickback will propel

the tool in direction opposite to the wheel’s movement at

the point of snagging.

• Use special care when working corners, sharp edges

etc. Avoid bouncing and snagging the accessory.

Corners, sharp edges or bouncing have a tendency to

snag the rotating accessory and cause loss of control or

kickback.

• Do not attach a saw chain woodcarving blade or

toothed saw blade. Such blades create frequent kickback

and loss of control.

Stanley SGV115 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info