Bedienungsanleitung Stanley SGV115 (Seite 9 von 28) (Englisch, Französisch)

720764

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

(Original instructions) ENGLISH

If the RCD causes power disconnection, have the tool sent to

an authorized Stanley dealer for repair.

WARNING! Under extreme working conditions, conductive

dust and grit may accumulate on the housing interior when

handling metal workpieces.

This could create an electric shock hazard as it weakens the

protective insulation in the grinder.

To avoid accumulation of metal chips in the interior of the

grinder, we recommend cleaning the ventilation ducts

daily.Refer to Maintenance.

Using Grinding Wheels

WARNING! Metal powder accumulates. Excessive use of the

grinding wheel on metals may increase the risk of electric

shock. To reduce the risk, insert the RCD before use and

clean the ventilation ducts daily. Follow the maintenance

instructions below to blow dry compressed air into the

ventilation ducts.

GRINDING

Surface Grinding with Grinding Wheels

1. Allow the tool to reach full speed before touching the tool

to the work surface.

2. Apply minimum pressure to the work surface, allowing the

tool to operate at high speed. Grinding rate is greatest

when the tool operates at high speed.

3. Maintain a 20˚ to 30˚ angle between the tool and work

surface.

4. Continuously move the tool in a forward and back motion

to avoid creating gouges in the work surface.

5. Remove the tool from work surface before turning tool off.

Allow the tool to stop rotating before laying it down.

Precautions to Take when Sanding Paint

• Sanding of lead based paint is NOT RECOMMENDED

due to the difﬁculty of controlling the contaminated dust.

The greatest danger of lead poisoning is to children and

pregnant women.

• Since it is difﬁcult to identify whether or not a paint

contains lead without a chemical analysis, we recommend

the following precautions when sanding any paint.

GENERAL INFORMATION

Helpful Hints

• Hold your angle grinder with one hand on the body and

the other hand ﬁrmly around the side handle as shown in

Fig. J.

• Always position the guard so that as much of the exposed

disc as possible is pointing away from you. ff Be prepared

for a stream of sparks when the disc touches the metal.

• Maintain an angle between the disc and work surface (Fig.

J) of approximately 30° when grinding and 10°- 15° when

sanding (Fig. K) for best tool control, material removal, and

minimal loading.

CAUTION! Use extra care when grinding into a corner as a

sudden, sharp movement of the grinder may be experienced

when the wheel contacts a secondary surface.

WARNING! Always wear eye protection while operating this

power tool.

Pop-off Brushes

The motor will be automatically shut off indicating that the

carbon brushes are nearly worn out and that the tool needs

servicing. The carbon brushes are not user-serviceable. Take

the tool to an authorised STANLEY repair agent.

Maintenance

Your Stanley corded/cordless appliance/tool has been

designed to operate over a long period of time with a minimum

of maintenance. To ensure satisfactory operations, the tool

must be maintained and cleaned regularly

WARNING! To minimize the danger of serious personal

injury, please switch off the tool power and disconnect all

plugs before adjusting or removing/ installing any

accessory. Before reassembling the tool, press and release

the trigger switch to make sure the tool is already switched off.

WARNING! Before performing any maintenance on corded/

cordless power tools:

Lubrication

Stanley tools are properly lubricated at the factory

and are ready for use.

Tools should be lubricated regularly every year depending on

usage. (Tools used on heavy duty jobs and tools exposed to

heat may require more frequent lubrication.) This lubrication

should be attempted only by trained power tool repairperson’s

such as those at Stanley service centers or in other qualiﬁed

service personnel.

Cleaning

WARNING! Dust and grit from metal grinding often

accumulate on interior surfaces and could create an

electrical shock hazard if not cleaned out. Use only

mild soap and a damp cloth to clean the tool. Never

let any liquid get inside the tool; never immerse any

part of the tool into a liquid.

WARNING! Never use solvents or harsh chemicals

to clean non-metal parts of the tool. These

chemicals may weaken the material of the parts.

Use only mild soap and damp cloth to clean the

tool. Never let any liquid get inside the tool; never

immerse any part of the tool into liquid.

WARNING! Do not overload your angle grinder.

Overloading causes a reduction in speed and

efﬁciency, causing your angle grinder to become too

hot. If this happens, operate your angle grinder

under no load for one or two minutes until it has

cooled to normal operating temperature. Switching

your angle grinder off under load will reduce the life

of the switch.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SGV115 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info