Bedienungsanleitung Stanley SJ60 (Seite 8 von 52) (Englisch, Französisch, Türkisch)

720786

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

ENGLISH (Original instructions)

2.Do not touch the blade or the workpiece immediately after

operation, they may be extremely hot and could burn your

skin.

3.Always secure the blade ﬁrmly. Insufﬁcient tighten of the

blade may cause blade breakage or serious personal injury.

4. Use only T type blades. Using blades other than T type

blades cause insufﬁcient tightening of the blade, resulting in a

serious personal injury.

5. Use suitable saw blade for different type of the workpieces

for getting better cutting result.

Connecting a vacuum cleaner to the tool (Fig.C)

• Slide the vacuum nozzle (14) into the dust extraction

outlet (10).

Residual risks

Additional residual risks may arise when using the tool which

may not be included in the enclosed safety warnings. These

risks can arise from misuse, prolonged use etc.

Even with the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks can not be avoided. These include:

• Injuries caused by touching any rotating/moving parts.

• Injuries caused when changing any parts, blades or

accessories.

• Injuries caused by prolonged use of a tool. When using

any tool for prolonged periods ensure you take regular

breaks.

• Impairment of hearing.

• Health hazards caused by breathing dust developed when

using your tool (example:- working with wood, especially

oak, beech and MDF.)

USE

Adjusting the shoe plate for bevel cuts (Fig. D)

Warning! Never use the tool when the shoe plate is loose or

removed. Always secure the shoe plate ﬁrmly before using

power tool. Insufﬁcient tightening of the shoe plate may cause

serious personal injury.

The shoe plate (9) can be set to a left or right bevel angle of

45°.

• Lift dust cover (4).

• Loosen the two screws-shoe plate (15).

• Pull the shoe plate (9) forward, rotate the shoe plate to the

left or right and push it back into the 45° location.

• Tighten the screws-shoe plate (15).

To reset the shoe plate for 90° cuts:

• Loosen the two screws-shoe plate (15).

• Pull the shoe plate (9) forward, rotate to the centre and

push it back into the 0° location.

• Tighten the screws-shoe plate (15).

• Turn down dust cover (4).

• WARNING: Turn down the dust cover to prevent chips

from ﬂying. However, when making bevel cuts, lift it all the

way.

Variable speed control:

• (SJ60)(Fig.A-1): A speed controller (3) is located on the

top of the Jigsaw. The speed increases as the wheel is

turned from a low speed setting of 1 to a high speed

setting of 6.

• (SJ45)(Fig.E): A speed controller (3) is located on the top

of the trigger switch. Turn the speed controller to “+”

direction to increase speed and turn the speed controller

to “-” direction to decrease speed.

• Refer to the table to select the proper speed for the

workpiece to be cut. However, the appropriate speed may

differ with the type or thickness of the workpiece. In

general, higher speeds will allow you to cut workpieces

faster but the service life of the blade will be reduced.

• WARNING: If the tool is operated continuously at low

speeds for a long time, the motor will get overload and

heated up.

Switching on and off (Fig.A-1,Fig.A-2)

• To switch the tool on, press the trigger switch (1).

• For continuous operation, press the trigger switch (1), then

press the lock-on button (2).

• To switch the tool off, release the trigger switch. To switch

the tool off, when in continuous operation, press the trigger

switch once more and release it.

How to Use the Sightline Feature (Fig. F)

• Use a pencil to mark the cutting line.

• Position the jig saw over the line (16).

• Viewing from directly above the jig saw, the line of cut can

be followed easily.

Cutting mode (SJ60 only)

• Pendulum stroke or action provides a more aggressive

blade motion and is designed for cutting soft materials

such as wood or plastic. It provides a faster cut, but with a

less smooth cut across the material. Your jig saw has a

Pendulum Stroke dial. Use of this dial is explained in the

next section.

• Warning: Never use pendulum action to cut metal.

Workpiece to be cut Number on speed controller-SJ60 Speed of SJ45

Wood 5-6 high speed

Stainless steel 3-4

Mild steel 3-6 medium speed

Aluminum 3-6

Plastics 1-4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SJ60 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info