Bedienungsanleitung Stanley SLL360 (Seite 12 von 160) (Alle Sprachen)

622242

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

77137

Set Up

• Place laser tool on a ﬂ at, stable surface.

• If using the auto levelling feature move the pendulum /

transport lock to the unlocked position. The laser tool must

then be positioned in its upright position on a surface that

is within the speciﬁ ed compensation range.

• The laser tool can be placed in any orientation and be

functional only when the pendulum / transport lock is in the

locked position.

Mounting on an Accessories

• Position accessory in a place where it will not be easily

disturbed and near the central location of the area to

be measured.

• Set up the accessory as required. Adjust positioning to

be sure accessory base is near horizontal (within laser

tools compensation range).

• Mount the laser tool to the accessory using the

appropriate fastening method to be used with such

accessory / laser tool combination.

CAUTION:

• Do not leave the laser tool unattended on an

accessory without fully tightening the fastening

screw. Failing to do so may lead to the laser tool

falling and sustaining possible damage.

NOTE:

• It is best practice to always support laser tool with

one hand when placing or removing laser tool from an

accessory.

Operation

NOTE:

• See LED Descriptions for indications during operation.

• Before operating the laser tool always be sure to check the

laser tool for accuracy.

• In Manual Mode, Self-Levelling is OFF. The accuracy of the

beam is not guaranteed to be level.

• Laser tool will indicate when it is out of compensation

range. Reference LED Descriptions. Reposition laser tool

to be closer to level.

• When not in use, please be sure to power OFF the laser

tool and place the pendulum lock in the locked position.

Power

• Press

to turn laser tool ON.

• To turn laser tool OFF, repeatedly press

until the

OFF mode is selected OR press and hold

for ≥ 3

seconds to turn laser tool OFF while in any mode.

Mode

• Press

repeatedly to cycle through the available

modes.

Self-Levelling / Manual Mode

(See ﬁ gures

and

)

• The pendulum lock on the laser tool needs to be

switched to the unlocked position to enable self-

levelling.

• The laser tool can be used with the pendulum lock in the

locked position when it is required to position the laser

tool at various angles to project non-level straight lines

and/or points (where applicable).

Accuracy Check and

Calibration

NOTE:

• The laser tools are sealed and calibrated at the factory to

the accuracies speciﬁ ed.

• It is recommended to perform a calibration check prior to

its ﬁ rst use and then periodically during future use.

• The laser tool should be checked regularly to ensure its

accuracies, especially for precise layouts.

• When performing the accuracy checks, use as large of an

area / distance as possible. The greater the area / distance,

the easier to measure the accuracy of the laser.

• Transport lock must be in the unlocked position to

allow the laser tool to self-level before checking

the accuracy.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SLL360 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info