Bedienungsanleitung Stanley SLP3 (Seite 14 von 212) (Alle Sprachen)

622257

Zoom out

Zoom in

Vorherige Seite

1/212

Nächste Seite

77-318 / 77-319

Set Up

Mounting on Accessories

Tripod / Accessory Mount (See ﬁ gure

)

• Position a tripod / accessory in a place where it will not

be easily disturbed and near the central location of the

area to be measured.

• Set up the tripod / accessory as required. Adjust

positioning to be sure tripod head / accessory mounting

base is near horizontal.

• Remove the leg attachment from the laser tool for easier

mounting.

• Mount the laser tool to the tripod / accessory by pushing

up the center screw and tighten.

CAUTION:

• Do not leave the laser tool unattended on an

accessory without fully tightening the center

screw. Failing to do so may lead to the laser tool

falling and sustaining possible damage.

Key Hole Slot (See ﬁ gure

)

• Place a nail, screw, or similar object into a vertical

surface.

• Rotate the lower base of the laser tool and ﬂ ip the key

hole slot up.

• Carefully hang the laser tool onto the nail, screw, or

similar object by the key hole slot on the laser tool.

Magnetic Mount (See ﬁ gure

)

• Attach the laser tool to any supportive magnetic surface.

• ALWAYS conﬁ rm that the laser tool is securely attached

to the magnetic surface before leaving unattended.

CAUTION:

• Only mount to metallic objects that will not

be easily disturbed and check for adequate

magnetic strength before leaving unattended.

Failing to do so may lead to the laser tool falling

and sustaining possible damage.

NOTE:

• It is best practice to always support laser tool with

one hand when placing or removing laser tool from an

accessory.

• If positioning over a target, partially tighten the center

screw, align laser tool, and then fully tighten.

Operation

NOTE:

• See LED Descriptions for indications during operation.

• Before operating the laser tool always be sure to check the

laser tool for accuracy.

• In Manual Mode, Self-Levelling is OFF. The accuracy of the

beam is not guaranteed to be level.

• Laser tool will indicate when it is out of compensation

range. Reference LED Descriptions. Reposition laser tool

to be closer to level.

• When not in use, please be sure to power OFF the laser

tool and place the pendulum lock in the locked position.

Power

• Press

to turn laser tool ON.

• To turn laser tool OFF, repeatedly press

until the

OFF mode is selected OR press and hold

for ≥ 3

seconds to turn laser tool OFF while in any mode.

Mode

• Press

repeatedly to cycle through the available

modes.

Self-Levelling / Manual Mode

(See Figures

and

)

• The pendulum lock on the laser tool needs to be

switched to the unlocked position to enable self-

levelling.

• The laser tool can be used with the pendulum lock in

the locked position when it is required to position the

laser tool at various angles to project non-level straight

lines or points.

Applications

Plumb / Point Transfer

• Establish 2 reference points that need to be plumb.

• Align either the down laser beam or the up laser beam to a

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SLP3 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info