Bedienungsanleitung Stanley SML 77-322 (Seite 11 von 208) (Alle Sprachen)

622250

Zoom out

Zoom in

Vorherige Seite

1/208

Nächste Seite

77-322

Level Adjustment

• For easy reference, position the leg base in such a way that

the circular bubble is above one of the adjustable legs.

• The circular bubble should be centered in the vial.

• If adjustment is required, proceed as follows

(See Figure

) :

• Turn the rear adjustable legs to bring the circular

bubble to the edge of the vial as indicated.

• Center the circular bubble by turning the front

adjustable leg.

Operation

NOTE:

• See LED Descriptions for indications during operation.

• Before operating the laser tool always be sure to check the

laser tool for accuracy.

• In Manual Mode, Self-Levelling is OFF. The accuracy of the

beam is not guaranteed to be level.

• Laser tool will indicate when it is out of compensation

range. Reference LED Descriptions. Reposition laser tool

to be closer to level.

• When not in use, please be sure to power OFF the laser

tool and place the pendulum lock in the locked position.

Power

• Press

to turn laser tool ON.

• To turn laser tool OFF, repeatedly press

until the

OFF mode is selected OR press and hold

for ≥ 3

seconds to turn laser tool OFF while in any mode.

Mode

• Press

repeatedly to cycle through the available

modes.

Self-Levelling / Manual Mode (See Figure

)

• The pendulum lock on the laser tool needs to be

switched to the unlocked position to enable self-

levelling.

• The laser tool can be used with the pendulum lock in

the locked position when it is required to position the

laser tool at various angles to project non-level / plumb

straight lines or points.

Pulse Mode (See Figure

)

• When laser tool is ON, press

to turn ON / OFF

pulse mode.

• Pulse mode allows use with laser detector.

Applications

Plumb / Point Transfer

• Using the vertical laser beam, establish a vertical reference

plane.

• Position the desired object(s) until they are aligned with the

vertical reference plane to ensure object(s) are plumb.

• Establish 2 reference points that need to be plumb.

• Align either the down laser beam or the up laser cross to a

set reference point.

• The opposing laser beam(s) will be projecting a point which

is plumb.

• Position the desired object until the laser beam is aligned

with the second reference point that needs to be plumb

with the set reference point.

Level / Point Transfer

• Using the horizontal laser beam, establish a horizontal

reference plane.

• Position the desired object(s) until they are aligned with the

horizontal reference plane to ensure object(s) are level.

Square

• Using either of the vertical laser beams that cross the

horizontal laser beams, establish a point where the 2

beams cross.

• Position the desired object(s) until they are aligned with

both the vertical and horizontal laser beams to ensure

object(s) are square.

Pulse Mode (See Figure

)

• Setting laser tool to pulse mode allows use with optional

laser detectors.

Manual Mode (See Figure

)

• Disables self-levelling function and allows laser unit to

project a rigid laser beam in any orientation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SML 77-322 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info