Bedienungsanleitung Stanley SPS-900 (Seite 18 von 36) (Deutsch, Englisch)

720577

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

CAUTION:when you operate the machine please

avoid the contact with curbs, stones and other hard

objects, because the cutting line may break and the

trim line automatic stops working.

Maintenance and Care

Gear Lubrication

Check the ﬁlling of lubrication grease every 25

hours of operation.

- Use an Allen key to remove the plug screw by

turning (B29).

- When you cannot see any grease on the screw,

ﬁll approx. 5 g lubrication grease (DIY store) into

the gearbox case, and close the ller opening again.

Keep in mind that the gearbox case should never

be completely ﬁlled with lubrication grease.

Air ﬁlter

After working for longer time, you should clean the air

ﬁlter. Dust and pollen plug up the pores of the ﬁlter made

of foamed plastic.

- Remove the cover (B30), and wash the ﬁlter (B31)

in mild soap water. Caution: Do not use any

gasoline or solvent.

- Dry the ﬁlter before you insert it again.

In order not to shorten the service life of the engine, a

damaged air ﬁlter must be replaced at once.

Adjustment of Spark Plug

Check the spark plug air gap at least once a year or when

the engine starts poorly. The correct gap

between ignition ﬂag and ignition contact

is 0.6-0.7 mm (B32).

- Wait until the engine has cooled down completely.

- Loose the screw and remove the plastic cover (B33).

- Pull the spark plug cap (B34) off the spark plug,

and use the supplied spark plug wrench to

remove the spark plug by turning (B35).

- When the electrode is severely worn out or

reveals a strong incrustation, the spark plug must

be replaced with an equivalent plug.

A strong incrustation of the spark plug can be

caused by: Amount of oil is too high in the

gasoline mix, poor oil quality, old gasoline mix, or

plugged up air ﬁlter.

- Screw the spark plug by hand completely into the

thread. (Avoid jamming it)

- Use the supplied spark plug wrench to tighten the spark

plug.

- When using a torque wrench, the tightening

torque is 12-15 Nm.

- Plug the spark plug socket correctly on the plug.

Trimming the Line Knife

- When the trimming line is no longer cut clean

during feeding, use a ﬁle to re-sharpen the cutting edge

(B36). File in one direction and in the

speciﬁed angle.

Cleaning

Use a moist piece of cloth to clean the plastic parts.

Do not use any cleaning agents, solvents, or sharp

objects.

During the course of work, wet grass and weed

wraps around the drive shaft below the cutting

guard for technical reasons. Remove this, otherwise the

engine will overheat because of too much friction.

Periodical Checks

Keep in mind that following speciﬁcations relate to

normal usage. Owing to circumstances (longer

periods of daily work, severe dust exposure, etc.),

the speciﬁed intervals will become correspondingly

shorter.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SPS-900 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info