Bedienungsanleitung Stanley SS24 (Seite 18 von 20) (Portugiesisch, Spanisch)

720584

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

ENGLISH (Original Instructions)

♦Remove dust bag from the sander and gently shake or

tap the dust bag to empty.

♦Reattach the dust bag back onto the outlet and lock

into place by turning the dust bag collar clockwise.

FITTING REGULAR SANDING SHEETS (Figura 3)

WARNING: Make sure that the tool is switched off and

unplugged.

♦Soften the sanding sheet by rubbing its non-abrasive

side over the edge of a worktop.

♦Lift the paper clamp levers (d) upwards to release them

from the retaining grooves and open the paper clamps

(d) by pressing them down.

♦Place the sheet onto the sanding base (c).

♦Insert the edge of the sanding sheet into the front

paper clamp (d) as shown.

♦Lift the front paper clamp lever (d) upwards and locate

it in the retaining groove.

♦While keeping a slight tension on the sheet, insert the

rear edge of the sheet into the rear paper clamp (d).

♦Press the rear paper clamp lever (d) downwards and

locate it in the retaining groove.

WHEN USING THE DUST BAG, USE A PUNCH PLATE

AS PICTURE (FIGURE D) SHOW. PUNCH HOLES ON

THE SANDING PAPER.

♦Place the tool upside down.

♦Place the punch plate on the sanding paper to make

the punch plate front side is corresponding to the tool

forward,the correct place please see (Figura 4).

♦Then press the punch plate to punch holes on the

sanding paper.

WARNING: Be sure to remove the punch plate before

operating the tool.

USE

WARNING: Let the tool work at its own pace. Do

not overload.

Switching on and off

♦To switch the tool on, press the on/off switch (a) to

the”I”place, see (Figura 1)

♦To switch the tool off press the on/off switch to the

“0“place ,see (Figura 1)

Hints for optimum use (Figure 5)

♦Do not exert too much pressure on the tool.

♦Regularly check the condition of the sanding paper.

♦Replace when necessary.

♦It is better to sand along the grain of the wood.

♦When sanding new layers of paint before applying

another layer, use extra fine grit.

♦On very uneven surfaces, or when removing layers of

paint, start with a coarse grit. On other surfaces, start

with a medium grit. In both cases, gradually change to

a fine grit for a smooth finish.

♦Consult your retailer for more information on available

accessories.

Residual risks

Additional residual risks may arise when using the tool

which may not be included in the enclosed safety warnings.

These risks can arise from misuse, prolonged use etc.

Even with the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks can not be avoided. These include:

♦Injuries caused by touching any rotating/moving parts.

♦Injuries caused when changing any parts, blades or

accessories.

♦Injuries caused by prolonged use of a tool. When using

any tool for prolonged periods ensure you take regular

breaks.

♦Impairment of hearing.

♦Health hazards caused by breathing dust developed

when using your tool (example:- working with wood,

especially oak, beech and MDF.)

MAINTENANCE

Your STANLEY power tool has been designed to operate

over a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper

tool care and regular cleaning.

♦Regularly clean the ventilation slots in your tool using

a soft brush or dry cloth.

♦Regularly clean the motor housing using a damp cloth.

Do not use any abrasive or solvent-based cleaner.This

machine is not user-serviceable. If problems occur

contact an authorised repair agent.

Lubrication

Your power tool requires no additional lubrication.

Cleaning

WARNING: Blow dirt and dust out of the main

housing with dry air as often as dirt is seen

collecting in and around the air vents. Wear

approved eye protection and approved dust mask when

performing this procedure.

WARNING: Never use solvents or other harsh

chemicals for cleaning the non-metallic parts of

the tool. These chemicals may weaken the

materials used in these parts. Use a cloth dampened only

with water and mild soap. Never let any liquid get inside the

tool; never immerse any part of the tool into a liquid.

To maintain products SAFETY and RELIABILITY,

repair, carbon brush inspection and replacement, any

other maintenance or adjustment should be performed

by STANLEY Service Centers, always using Stanley

replacement parts.

OPTIONAL ACCESSORIES

WARNING: Since accessories, other than those

offered by STANLEY, have not been tested with

this product, use of such accessories with this

tool could be hazardous. To reduce the risk of injury, only

STANLEY, recommended accessories should be used

with this product.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SS24 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Stanley SS24

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info