Bedienungsanleitung Stanley SST1800 (Seite 4 von 36) (Englisch, Französisch)

720738

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

NOT use a fence or fence system for cross-cutting.

Instead, use a miter gauge. USE PUSH STICK(S) for

ripping a narrow workpiece.

• AVOID AWKWARD OPERATIONS AND HAND

POSITIONS where a sudden slip could cause a hand to

move into the blade

• KEEP ARMS, HANDS, AND FINGERS away from the

blade

• NEVER have any part of your body in line with the path of

the saw blade.

• NEVER REACH AROUND or over the saw blade.

• NEVER attempt to free a stalled saw blade without ﬁrst

turning the machine “OFF”.

• PROPERLY SUPPORT LONG OR WIDE workpieces.

• NEVER PERFORM LAYOUT, assembly or set-up work on

the table/work area when the machine is running.

• TURN THE MACHINE “OFF” AND DISCONNECT THE

MACHINE from the power source before installing or

removing accessories, before adjusting or changing

set-ups, or when making repairs.

• TURN THE MACHINE “OFF”, disconnect the machine

from the power source, and clean the table/work area

before leaving the machine. TURN THE SWITCH IN THE

“OFF” POSITION.

• Use push-sticks or push blocks to feed the workpice past

the saw blade

• Use and correct adjustment of the upper saw blade guard

• Do not use the saw blade if damaged or deformed.

• Use only the recommended saw blade, which conform to

EN847-1.

• When change saw blade, make sure the width of the

groove cut of the saw blade shall not be less than and the

thickness of the body of the saw blade shall not be more

than the thickness of the riving knife.

• Select the saw blade suitable for the material to be cut

• Wear suitable personal protective equipment include:

- hearing protection to reduce the risk of induced hearing

loss;

- eye protection

- respiratory protection to reduce the risk of inhalation of

harmful duct;

- gloves for handling saw blades and rough material (saw

blade should be carried in a holder wherever practicable)

• Connect to a dust-collecting device when sawing wood

• Do not use high speed steel (HS) saw blades

• Do not rebate or groove unless suitable guarding, such as

a tunnel guard, is ﬁtted above the saw table;

• Do not use saws for slotting (stopped groove)

• Use only saw blades for which the maximum possible

speed is not less than the maximum spindle speed of the

tool and the material to be cut.

ENGLISH (Original instructions)

e. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tools

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

5. Service

a. Have your power tool serviced by a qualiﬁed repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

TABLE SAWS SAFETY WARNINGS

Warning! Failure to follow these rules may result in

serious injury.

• DO NOT OPERATE THIS MACHINE until it is assembled

and installed according to the instructions.

• OBTAIN ADVICE FROM another qualiﬁed person if you

are not familiar with the operation of this machine.

• FOLLOW ALL WIRING CODES and recommended

electrical connections.

• ALWAYS USE THE GUARDS Check to see that they are

in place, secured, and working correctly.

• ALWAYS USE GUARDS, SPLITTER.

• REMOVE CUT-OFF PIECES AND SCRAPS from the

table before starting the saw. The vibration of the machine

may cause them to move into the saw lade and be thrown

out. After cutting, turn the machine off. After the blade has

come to a complete stop, remove all debris.

• NEVER START THE MACHINE with the workpiece

against the blade.

• NEVER run the workpiece between the fence and a

moulding cutterhead.

• CUTTING THE WORKPIECE WITHOUT THE USE OF A

FENCE OR MITER GAUGE IS KNOWN AS

“FREEHAND” CUTTING. NEVER perform “freehand”

operations. Use either the fence or miter gauge to position

and guide the workpiece.

• HOLD THE WORKPIECE FIRMLY against the miter

gauge or fence.

• CUTTING COMPLETELY THROUGH THE WORKPIECE

IS KNOWN AS “THROUGH-SAWING”. Ripping and

cross-cutting are through-sawing operations. Cutting with

the grain (or down the length of the workpiece) is ripping.

Cutting across the grain (or across the workpiece) is

cross-cutting. Use a fence or fence system for ripping. DO

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SST1800 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info